manualshive.com logo in svg

Wacker Neuson E3000, Руководство оператора

Поделиться
Скачать
Wacker Neuson E3000 Скачать руководство пользователя страница 158

 wc_tx002068gb.fm

158

Genset Maintenance

Onan Genset

Continued from the previous page.

7. Unscrew the oil filter 

(c)

 and remove it through the front access opening.

8. Clean the oil filter mounting surface of the engine.

Filling

1. Apply a thin coat of clean oil to the gasket of the new oil filter.

2. Thread the oil filter onto the engine until the gasket touches the block. Then, 

turn the oil filter an additional 180°–270°.

3. Refill the engine with 1.7 qt (1.9 liters) of oil.

4. Reinstall the access covers.

5. Start the genset and allow it to run for a 1–3 minutes.

6. Check the oil level. Add oil as needed.

Result

The engine oil and oil filter have now been changed.

  

wc_gr008035

c

WARNING

Most used oil contains small amounts of materials that can cause cancer and other 
health problems if inhaled, ingested, or left in contact with skin for prolonged 
periods of time.

f

Take steps to avoid inhaling or ingesting used engine oil. 

f

Wash skin thoroughly after exposure to used engine oil.

Содержание E3000























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды