Wacker Neuson E3000 Скачать руководство пользователя страница 135

Страница: 135 / 214

wc_tx001803gb.fm

135

E 3000

Maintenance

8.2

Inspecting the HTF System and the Fuel System

Requirements

Machine shut down

Burner cool

HTF System

Hoses:

1. Rotate the hose reel brake T-handle counterclockwise to release the brake.

2. Unwind all the hose off the reel. Inspect the hose for leaks and/or damage.

3. Repair any leaks and repair/replace any damaged hoses. See topic

Repairing a

Hose

4. Turn on the machine and rewind the hose onto the reel.

5. Engage the brake by turning the T-handle clockwise.

Pump, motor, and hydronic heater:

1. Inspect the pumps and motor assemblies and associated plumbing for leaks

and/or damage.

2. Inspect hydronic heater and associated plumbing for leaks and/or damage.

3. Repair/replace any damaged components.

4. Repair any leaks.

Fuel System

Burner:

1. Inspect all fuel hoses and connections for leaks and/or damage.

2. Inspect the fuel filter and associated fuel hoses for leaks and/or damage.

3. Repair/replace any damaged hoses, pipes, or connectors.

4. Repair any leaks.

Fuel tank:

1. Inspect all fuel hoses

running into and out of the fuel tank for leaks and/or dam-

age.

2. Repair/replace any damaged hoses, pipes, or connectors.

3. Repair any leaks.

Содержание E3000























































































































































































































Результаты поиска

Содержание E3000

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson E3000, Руководство оператора

Результаты поиска

Содержание E3000

Отзывы:

Бренды по названию

Популярные бренды