Wacker Neuson E3000 Скачать руководство пользователя страница 37

Страница: 37 / 214

ghi_tx001160gb.fm

E 3000

Lifting and Transporting

Continued from the previous page.

5. If the brakes did not function, check the voltage of the breakaway battery. To do

so:
a. Remove the cover of the battery box.
b. Remove the wires connected to the breakaway battery

(d)

c. Measure the voltage. If 12–14 VDC is not measured, replace or recharge the

breakaway battery.

6. If 12–14 VDC was measured but the brakes did not function, there is a wiring or

mechanical fault with the brakes. Repair any faults before towing.

7. If the brakes function properly:

a. Reconnect the wires to the breakaway battery.
b. Reinstall the cover to the battery box.
a. Reinstall the breakaway pin

(b)

into the brake switch.

b. Connect the trailer wiring plug to the tow vehicle.

Result

The procedure to test the breakaway system is now complete.

wc_gr008472

VDC

1000

200

200m

V-

COM

Содержание E3000























































































































































































































Результаты поиска

Содержание E3000

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson E3000, Руководство оператора

Результаты поиска

Содержание E3000

Отзывы:

Бренды по названию

Популярные бренды