manualshive.com logo in svg

Wacker Neuson E3000, Руководство оператора

Поделиться
Скачать
Wacker Neuson E3000 Скачать руководство пользователя страница 16

Safety Information

E 3000

 wc_si000579gb.fm

16

1.6

Safety Guidelines for Operating Gensets

This machine is built with user safety in mind; however, like any electrical device it 
can present serious hazards if improperly operated and serviced. Follow 
instructions carefully. Should questions arise during operation or service of this 
equipment, contact your Wacker Neuson dealer.

General 
precautions

„

Keep a multi-class, type ABC or equivalent fire extinguisher at hand when using 
the genset. Refer to NFPA No. 10 for further information regarding fire 
extinguishers.

„

Do not use evaporative starting fluids. They are highly explosive.

„

Do not store items such as excess oil, oil rags, tools within the genset 
compartment. Items stored within the genset compartment are a fire hazard and 
can restrict cooling air.

„

Wash thoroughly after handling used engine oil.

DANGER

f

Carbon monoxide.

 Using a generator indoors CAN KILL YOU IN MINUTES. 

Generator exhaust contains carbon monoxide (CO). This is a poison you cannot 
see or smell. If you can smell the generator exhaust, you are breathing CO. But 
even if you cannot smell the exhaust, you could be breathing CO.

WARNING

Electrocution hazard. 

Generators present special hazards during operation and 

servicing. These include the risk of electrocution or severe electrical shock. Failure 
to follow the safety information below can result in severe injury or death.

f

Read and follow the safety instructions in this Operator’s Manual. 

f

Contact the genset manufacturer for additional information regarding the 
genset.

WARNING

Internal combustion engines present special hazards during operation and fueling. 
Failure to follow the warnings and safety instructions could result in severe injury or 
death.

f

Read and follow the safety instructions in this Operator’s Manual. 

f

Contact the genset manufacturer for additional information regarding the 
genset.

WARNING

Most used oil contains small amounts of materials that can cause cancer and other 
health problems if inhaled, ingested, or left in contact with skin for prolonged 
periods of time.

f

Take steps to avoid inhaling or ingesting used engine oil. 

f

Wash skin thoroughly after exposure to used engine oil.

Содержание E3000























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды