Wacker Neuson E3000 Скачать руководство пользователя страница 30

Страница: 30 / 214

ghi_tx001160gb.fm

Lifting and Transporting

E 3000

Lifting and Transporting

3.1

Lifting the Machine

Requirements

Properly rated lifting equipment (crane or hoist). See Chapter

Technical Data

Machine stopped. See topic

Stopping the Machine

All doors and access covers closed and secured.

Procedure

Follow the procedure below to lift the machine.

1. Attach the lifting equipment to one of the lifting eyes

(a)

on the machine using

hooks, shackles, and chains.

2. Lift the machine a small distance.

3. Check for stability. If necessary, lower the machine, reposition the lifting device,

and lift the machine a small distance again.

4. Continue lifting the machine as necessary.

WARNING

Crushing hazard. You may be crushed if the lifting devices fail.

Never stand under, or get onto, the machine while it is being lifted or moved.

Use only the designated lifting points to lift the machine.

WARNING

Crushing hazard. An unstable machine may cause the lifting devices to fail. You
may be crushed if the lifting devices fail.

Check for stability before continuing.

Содержание E3000























































































































































































































Результаты поиска

Содержание E3000

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson E3000, Руководство оператора

Результаты поиска

Содержание E3000

Отзывы:

Бренды по названию

Популярные бренды