Wacker Neuson E3000 Скачать руководство пользователя страница 167

Страница: 167 / 214

wc_tx002068gb.fm

167

Onan Genset

Genset Maintenance

Governor overload fault

The duration of operation at or near full-duty
cycle was beyond the design limit.

1. Disconnect any extra loads.

2. Check for and repair fuel leaks. Air in the fuel

supply can disrupt frequency. Prime the
engine fuel system by holding the control
switch at Stop for one minute.

3. Replace the engine air filter.

4. Clean the spark arrestor.

5. Replace the fuel filter.

Temperature sender fault

The controller sensed that the sender circuit is
either open or shorted

See authorized Cummins Onan dealer.

AC voltage sensed fault

The controller was unable to sense output volt-
age.

See authorized Cummins Onan dealer.

High battery voltage fault

The controller sensed battery system voltage
greater than 19 volts.

See authorized Cummins Onan dealer.

Low cranking speed fault

Cranking speed less than 100 rpm (2.5 Hz) for
more than 12 seconds.

1. Clean and tighten the battery connections.

2. Recharge or replace the battery.

3. Replace the engine oil with oil of the proper

viscosity for the ambient temperature.

Control card fault

Microprocessor EEPROM error during self test

See authorized Cummins Onan dealer.

Engine stopped fault

The genset stopped without a command from
the controller.

1. Check fuel level; refill fuel tank.

2. Check for and repair fuel leaks. Air in the fuel

supply can disrupt frequency. Prime the
engine fuel system by holding the control
switch at Stop for one minute.

3. Replace engine air filter.

4. Replace the fuel filter.

Field overload fault

Field voltage exceeded 150VDC

See authorized Cummins Onan dealer.

Shorted rotor fault

The rotor circuit is shorted to ground.

See authorized Cummins Onan dealer.

Processor fault

Microprocessor ROM error during self test

See authorized Cummins Onan dealer.

Processor fault

Microprocessor RAM error during self test

See authorized Cummins Onan dealer.

Speed sense fault

Controller unable to sense quadrature fre-
quency

1. Check fuel level; refill fuel tank.

2. Check for and repair fuel leaks. Air in the fuel

supply can disrupt frequency. Prime the
engine fuel system by holding the control
switch at Stop for one minute.

Code

Fault Type

Corrective Action

Содержание E3000























































































































































































































Результаты поиска

Содержание E3000

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson E3000, Руководство оператора

Результаты поиска

Содержание E3000

Отзывы:

Бренды по названию

Популярные бренды