Volvo Penta D25A MS Скачать руководство пользователя | Manualshive

Страница: 83 / 87

background image

83

Technical Data

Identification numbers D25A / D30A

Type plates with identification numbers can be found on the engine and the transmission or generator. This infor-
mation must always be used as a reference when ordering service and spare parts.

Engine .........................................................................................................................................
Product designation .....................................................................................................................

Serial and basic engine number ..................................................................................................
Product number ...........................................................................................................................

Certification, IMO .........................................................................................................................
Decal, part No. ............................................................................................................................

Approval No. ................................................................................................................................

Transmission / Generator ............................................................................................................

Product designation .....................................................................................................................
Serial number ..............................................................................................................................

Product number ...........................................................................................................................

Plus d'informations sur : www.dbmoteurs.fr

«
...
81
82
83
84
85
...
»

Содержание D25A MS
























































































Отзывы:

Нет отзывов

Похожие инструкции для D25A MS

Бренд: Rato Страницы: 65

Era-Era Star Head EMPC

Бренд: Nice Страницы: 2

Бренд: Eaton Страницы: 16

Бренд: Nice Страницы: 23

Бренд: Westerbeke Страницы: 65

Бренд: Doosan Страницы: 108

Бренд: Lenze Страницы: 36

Бренд: Man Страницы: 50

Бренд: Pacific Страницы: 48

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 99

Бренд: Yamaha Страницы: 128

Бренд: Yamaha Страницы: 135

Бренд: Yamaha Страницы: 144

Бренд: Yamaha Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды