Volvo Penta D25A MS Скачать руководство пользователя страница 46

Страница: 46 / 87

Maintenance: Fuel System

Fuel filter change

Switchable fuel filters can be changed while the engine is running as the flow of fuel can be cut off to one filter at a
time.

WARNING!

Working on or approaching a running engine is a safety hazard. Beware of rotating parts and hot

surfaces.

A. Right Filter bleed position

B. Right Filter change position

C. Neutral position

D. Left Filter change position

E. Left Filter bleed position

1. Place a drip pan under the fuel filter.

2. Put the fuel filter switching cock in the Left filter

change position and unscrew the left-hand fuel fil-
ter. Use a filter wrench if necessary.

3. Coat the gasket of a new filter with clean diesel

fuel.

4. Install the new filter in the filter bracket by hand.

When the gasket contacts the base, tighten 1/2 to
3/4 of a turn more.

5. Put the fuel filter switching cock in the Left filter

bleed position and loosen the left air vent plug un-
til the fuel running out is free from air. Close the
air vent.

6. Put the fuel filter switching cock in the neutral po-

sition and repeat the above described procedure
for the other fuel filter.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D25A MS
























































































Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды

Volvo Penta D25A MS, Руководство оператора

Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды