Volvo Penta D25A MS Скачать руководство пользователя страница 53

Страница: 53 / 87

Maintenance: Fuel System

Close the fuel cocks on the tank or cut off the flow of
fuel with the knob (1) for the filter insert to change if
running.

WARNING!

Working on or approaching a

running engine is a safety hazard. Beware of
rotating parts and hot surfaces.

1. Place a receptacle under the filter.

2. Undo the T-bolt (2) and remove the cover (3).

3. Take out the insert carefully while turning it.

4. Drain off water and contaminants through the

drain plug (4).

5. Fit a new filter insert and fill the container with cle-

an fuel.

IMPORTANT!

Cleanliness! No contaminants

must be allowed in the fuel system.

6. Change the gasket on the cover and the O-ring

on the T-bolt. Moisten the gasket and O-ring with
fuel before assembling.

7. Fit the cover and tighten it by hand.

8. Wipe off any fuel from the heat shield.

9. Dual filter: Change the other filter insert in the

same way.

10. Open the fuel cocks and put the knob (1) in posi-

tion for normal running. Make sure there are no
leaks.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D25A MS
























































































Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды

Volvo Penta D25A MS, Руководство оператора

Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды