Volvo Penta D25A MS Скачать руководство пользователя страница 54

Страница: 54 / 87

Maintenance: Lubrication system

Lubrication system

Lubrication oil level check

The oil level must be within the marked range on the
dipstick and must be checked daily.

IMPORTANT!

The level must never be allowed

to drop beneath the minimum or rise above the
maximum mark on the dipstick.

Lubrication oil filling

Fill the engine with lubrication oil through the filler
pipe. For oil specification refer to chapter technical
data. The oil level should be within the marked area
on the dipstick. After filling oil, secure filler cap.

WARNING!

Lubrication oil on hot surfaces or

electrical components may cause fire. Do not
smoke while filling oil or when handling oil con-
tainers.

IMPORTANT!

Stop the engine when filling oil.

IMPORTANT!

Avoid mixing oils of different

brands, additives used in the oils can cause
chemical reactions that may degrade the oil
performance.

IMPORTANT!

The lubrication oil level must

never be allowed to drop beneath the lower, or
rise above the maximum, mark on the dipstick.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D25A MS
























































































Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды

Volvo Penta D25A MS, Руководство оператора

Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды