Volvo Penta D25A MS Скачать руководство пользователя страница 31

Страница: 31 / 87

MAINTENANCE SCHEDULE D25A/D30A MS

Daily before first start

* General inspection engine and engine room

* Check and make sure all valves are in the right position

* Check lubrication oil level

* Check marine gear oil level

* Check lubrication oil filter differential pressure indicator

* Check air-filter differential pressure indicator

* Check coolant level

* Check fuel oil level

* Drain water from fuel tank

* Drain water from fuel pre-filter/water separator

* Drain water from air vessel and air filter

* Check engine control system (cables, etc.)

* Check fuel control linkage

* Check for leakages

* Check aftercooler drain pipe

* Daily operation records

* Inspection of valves and plugs

* Check if the instrumentation works properly

Weekly

* Check starting batteries; electrolyte level/load

* Check electrical system for loose terminals/contacts

* Check foundation bolts

* Check lubrication oil for abnormal smell or waterdilution

* Check safety valves of air system

* Check air system oiler

* Check settings of valves and move valve to keep them operationable

* Drain water from the fuel pre-filter/water separator

First 50-250 operating hours of new or recond. engines (First service)

* Change lubrication oil

* Change full flow and by-pass lubrication oil filters

* Change governor lubrication oil filter

* Check required lubrication oil change for marine gear

* Check/adjust V-belts

* Check/adjust valve clearance

* Check/adjust stop solenoid and/or fuel stop valve

* Check/retighten bolts and nuts

* Drain crankcase ventilation water trap

* Drain exhaust silencer(system) water trap

Plus d'informations sur : www.dbmoteurs.fr

Содержание D25A MS
























































































Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды

Volvo Penta D25A MS, Руководство оператора

Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды