Volvo Penta D25A MS Скачать руководство пользователя страница 57

Страница: 57 / 87

Maintenance: Lubrication system

Oil filter change

The oil filters can be changed while the engine is run-
ning as the oil flow can be directed through one filter
at a time.

1. Remove the cover from the filter switch valve by

disconnecting the two bolts.

WARNING!

Working on or approaching a

running engine is a safety hazard. Beware of
rotating parts and hot surfaces.

4. Lightly oil the new filter’s rubber gasket and check

its mating surface on the mounting.

5. Mount the new filter by hand until the gasket is in

contact with the sealing surface. Then tighten the
filter a further approximately 3/4 of a turn using a
filter wrench.

6. Put the filter on-line by turning the valve in posi-

tion A.

7. Replace the left filter as above. Position B is the

left filter change position.

8. Replace both full-flow filters and the by-pass filter

at the same change interval. Refere to next page
for by-pass oil filter change procedure.

NOTE!

After a lubrication oil filter change, open the

filter and check for metal parts.

2. Cut off the oil flow through the right filter by tur-

ning the setting valve in position C.

3. Unscrew the oil filter using the special tool. Dis-

card the filter.

NOTE!

Place a container beneath the filter when

removing to avoid oil spill.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D25A MS
























































































Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды

Volvo Penta D25A MS, Руководство оператора

Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды