Volvo Penta D25A MS Скачать руководство пользователя страница 63

Страница: 63 / 87

Seawater pump impeller check/
hange

IMPORTANT!

Always keep a spare impeller and

gasket in store.

1. Drain the external cooling water as described in

the chapter draining the seawater system.

2. Remove the pump end cover and the impeller.

3. Inspect the impeller. Change the impeller if there

are any visible cracks or other defects.

4. Clean the inside of the housing. Lubricate the

pump housing and the inside of the cover with
water-resistant grease (non-aggressive on rub-
ber).

5. Push the impeller into position while rotating it in

the normal operating direction.

6. Fit the cover with a new gasket.

7. Open the seawater cocks.

Heat exchanger cleaning

Clean if there are signs of clogging, a gradual increa-
se in engine temperature or high seawater pressure.
Check/clean the seawater filter first. Check also the
seawater pump impeller.

1. Drain the external cooling water as described in

the chapter draining the seawater system.

2. Detach the pipe connections from the heat ex-

changer.

3. Remove both covers from the heat exchanger

4. Clean the heat exchanger insert pipe using suita-

ble brushes while flushing through the pipe with
water

5. Refit the heat exchanger element and mound the

covers.

6. Connect the pipe connections to the heat exchan-

ger. Check gaskets and change if necessary.

7. Open the seawater cocks. Fill the freshwater sys-

tem.

8. Start the engine and make sure the seawater sys-

tem is not leaking.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D25A MS
























































































Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды

Volvo Penta D25A MS, Руководство оператора

Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды