Volvo Penta D25A MS Скачать руководство пользователя | Manualshive

Страница: 16 / 87

background image

16

General

Before starting a new or reconditioned engine for the first time, give it an initial inspection. This to guarantee your
own safety as well as the maximum service life of the engine.

New Engine Initial service

External Inspection

1. Check the engine control system for loose termin-

als.

2. Check defects of engine parts.

3. Check the following components for loose bolts or

nuts:

* Plugs and covers of fuel, lubrication and cooling

system

* Coupling of fuel injection pump and shaft

* Crankshaft pulley and vibration damper

* Mounting brackets

* Fuel control linkage

* Turbocharger

* Timing gear case

* Exhaust manifolds

* Cylinder heads

* Air-duct connection-hose clamp

4. Check for Fuel, Oil, Coolant and Air leaks and rep-

air if needed.

5. Make commissioning report for new or overhauled

engine.

IMPORTANT!

All covers must be mounted before

attempting to start your engine.

Valves and Plugs

Make sure the following valves and plugs are open or
closed properly:

Fuel supply valve

Open

Coolant drain cock (engine)

Closed

Coolant drain cock (water pump)

Closed

Coolant drain cock (heat exchanger) Closed

IMPORTANT!

If the coolant drain cocks are not

closed the coolant will drain from the engine and
this may cause severe damage to the engine.

Electrical Wiring

Check for loose or damaged electrical wiring around
the engine and if necessary firmly reconnect to ter-
minals or cable-joint portions. Damaged cables must
be replaced.

If your engine is reconditioned, make sure the wiring
is according to the drawings.

Fill Fuel system

Refer to chapter maintenance fuel system.

Fill Lubrication system

Refer to chapter maintenance lubrication system.

Fill Cooling system

Refer to chapter maintenance cooling system.

Plus d'informations sur : www.dbmoteurs.fr

«
...
14
15
16
17
18
...
»

Содержание D25A MS
























































































Отзывы:

Нет отзывов

Похожие инструкции для D25A MS

Бренд: Flux Страницы: 16

Бренд: D-MOTOR Страницы: 48

Automate RF 500 Series

Бренд: Acmeda Страницы: 8

Бренд: Champion Power Equipment Страницы: 20

Бренд: Tanaka Страницы: 11

Lombardini SILEO 1000

Бренд: Kohler Страницы: 168

Lombardini LGW 523 MPI

Бренд: Kohler Страницы: 144

Бренд: MTU Страницы: 156

Бренд: Sachs Страницы: 42

PowerLine TG500B

Бренд: Texas Страницы: 98

Бренд: Vetus Страницы: 28

Бренд: Kober Страницы: 112

Бренд: Yamaha Страницы: 51

Бренд: Mercury/Mariner Страницы: 130

Бренд: Mercury Страницы: 18

Бренд: Mercury Страницы: 9

Бренд: Mercury Страницы: 85

Бренд: MerCruiser Страницы: 895

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды