Volvo Penta D25A MS Скачать руководство пользователя страница 70

Страница: 70 / 87

Technical Data

D25A MS

General

Type designation

D25A-MS

Number of cylinders ..............................................

Displacement .........................................................

24,51 liters (1496 in

)

Nominal idling speed .............................................

not available

Low idling speed ....................................................

625 ±25 rpm

High idling speed ...................................................

not available[rating 1]

not available[rating 2]

Valve clearance* ...................................................

0,6 mm (0,024”) [inlet]

0,8 mm (0,031”) [outlet]

Compression pressure
at starter motor speed (120 rpm) ..........................

not available

Dry weight engine, without oil and coolant
without reverse gear or clutch, approx. ................

2320 kg (5116 lbs)

Exhaust temperatures:

440 kW Rating 1

1008 r/min. .............................................................

300°C/(527°F)

1270r/min. ..............................................................

380°C/(716°F)

1454 r/min. .............................................................

390°C/(734°F)

1600 r/min. .............................................................

380°C/(716°F)

Exhaust temperatures:

485 kW Rating 2

1039 r/min. .............................................................

348°C/(658°F)

1310r/min. ..............................................................

440°C/(824°F)

1500 r/min. .............................................................

445°C/(833°F)

1650 r/min. .............................................................

450°C/(842°F)

* Applies to cold engine.

Lubricating system

Oil capacity, approx.

Including oil filters

No engine inclination .............................................

160 liters (42,3 US gals)

volume difference min. –max. ..............................

30 liters (7,9 US gals)

Oil pressure, hot engine:

at operating speed .................................................

0,50-0,64 MPa (71-93 psi)

at idling speed .......................................................

min.0,20-0,30 MPa (29-43 psi)

Cooling system

Freshwater system capacity
including heat exchanger, approx. ........................

50 liters (13,2 US gals)

Electrical system

System voltage .....................................................

24V

AC generator:

voltage/max. amperage .........................................

24V/35A

output, approx. ......................................................

840W

Battery electrolyte density at +25°C (77°F):

fully charged battery ..............................................

1,28 g/cm

= 0,0462 lb/in

(1,24 g/cm

= 0,0448 lb/in

battery recharged at ..............................................

1,24 g/cm

= 0,0448 lb/in

(1,20 g/cm

= 0,0434 lb/in

* Note.

Applies to batteries with tropical acid.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D25A MS
























































































Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды

Volvo Penta D25A MS, Руководство оператора

Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды