Volvo Penta D25A MS Скачать руководство пользователя страница 55

Страница: 55 / 87

Maintenance: Lubrication system

Filling oil in new or reconditioned engine

If your engine is new or reconditioned you should
besides the actual filling of new lubrication oil also do
the following:

1. Remove the rocker cover. Lubricate the valve

mechanism and fill the camshaft oil bath from the
cylinder head. Repeat the procedure for each cy-
linder.

2. Mount all the rocker covers. Refer to section

Tightening torques for proper torques.

NOTE!

Avoid running or cranking the engine without

the rocker covers mounted.

3. Remove the lubrication oil pipe connected to the

turbo.

Fill the turbo through the opening with 2 or 3
pumps of oil from the oil fill can. This has to be
done to secure lubrication of the turbo during the
first start-up.

IMPORTANT!

Do not bend the pipe. This can

block the oil supply to the turbo.

4. Reconnect the lubrication oil pipe to the turbo pro-

perly.

5. Crank the engine 3 times for maximum 10 se-

conds with the emergency stop lever in the stop
position and check if the oil pressure rises proper-
ly.

6. Start the engine and operate it for about 10 minu-

tes and check if the oil pressure rises properly.
Check the oil pan and related parts for oil leaks.

IMPORTANT!

If oil pressure do not rise

immediately after start, stop the engine and
investigate. Do not restart until problem is fixed.

7. Check the oil level in the oil pan and add oil if ne-

cessary.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D25A MS
























































































Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды

Volvo Penta D25A MS, Руководство оператора

Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды