Volvo Penta D25A MS Скачать руководство пользователя страница 20

Страница: 20 / 87

Standard Control System

Starting procedure

1. Disengage the reverse gear and make sure the

turning gear is not engaged. Put the control lever
into neutral and idle on all control positions

WARNING!

If the vessel is equipped with

controls that allow starting the engine in
gear, it is essential to check all control
positions to make sure a gear is not
engaged.

2. Turn on the power by putting the starter key in po-

sition “I”.

4. Start the engine. Start using the starting switch.

Turn the key to position “III”. Release the key so
that it returns to “I” immediately after the engine
has started.

IMPORTANT!

If the starter motor has been

engaged for the maximum time (30
seconds), it must be allowed to cool down for
at least one minute before a new attempt is
made at starting.

NOTE!

The key must first be turned to “S” before ma-

king a new attempt at starting.

5. Check the instruments and run the engine

warm.

Let the engine idle for the first ten seconds

and make sure the instruments and warning dis-
play show normal values. Then run the engine at
low speed and low load so it attains normal opera-
ting temperature before using full power.

IMPORTANT!

Do not race the engine when it

is cold.

3. Check warning lamps and alarms. Press the

“Alarm test” button on the instrument panel to
make sure the warning lamps come on and the
acoustic alarm sounds.

Plus d'informations sur : www.dbmoteurs.fr

Содержание D25A MS
























































































Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды

Volvo Penta D25A MS, Руководство оператора

Результаты поиска

Содержание D25A MS

Отзывы:

Похожие инструкции для D25A MS

Бренды по названию

Популярные бренды