Volvo Penta D25A MS Скачать руководство пользователя | Manualshive

Страница: 6 / 87

background image

6

Safety Information

Read this chapter thoroughly. It concerns your safety. This section describes how safety information is presented
in this manual and on the product. It also includes a summary of basic safety regulations for operation and main-
tenance of the engine.

Make sure you are in possession of the right operator’s manual before reading on. If this is not the case,
please get in touch with your Volvo Penta dealer.

If operations are performed incorrectly it could result in personal injury or damage to property or the engi-
ne. Read the Operator’s Manual carefully before operating or servicing the engine. If anything is unclear
please contact your Volvo Penta dealer for assistance.

This symbol is used in the book and on the engine to make you aware of safety infor-

mation. Always read these safety precautions very carefully.

In the Operator’s Manual warning texts have the following priority:

WARNING!

If these instructions are not followed there is a danger of personal injury,

extensive damage to the product or serious mechanical malfunction.

IMPORTANT!

Used to draw your attention to something that can cause damage,

product malfunction or damage to property.

NOTE!

Used to draw your attention to important information that will facilitate work or

operations.

This symbol is used in certain cases on our products and refers to important informa-

tion in the Operator’s Manual. Ensure that warning and information symbols on the engine
and transmission are always visible and legible. Replace symbols that have been damaged
or painted over.

Plus d'informations sur : www.dbmoteurs.fr

«
...
4
5
6
7
8
...
»

Содержание D25A MS
























































































Отзывы:

Нет отзывов

Похожие инструкции для D25A MS

Бренд: O.S. engine Страницы: 32

Бренд: D+H Страницы: 20

Бренд: brel-motors Страницы: 2

Бренд: Westerbeke Страницы: 110

Reliance CDX7150

Бренд: Baldor Страницы: 32

Бренд: Kohler Страницы: 4

Бренд: Mile HaoXianG Model Technology Страницы: 3

Бренд: Kubota Страницы: 47

Бренд: Kubota Страницы: 181

Бренд: Andersen Страницы: 20

Бренд: Briggs & Stratton Страницы: 60

Бренд: O.S. engine Страницы: 13

MAX-15CV Series

Бренд: O.S. engine Страницы: 30

Бренд: BAFANG Страницы: 6

Бренд: Seg Страницы: 21

Бренд: Clarke Страницы: 49

Бренд: Maverick Страницы: 12

Бренд: Masport Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды