Volvo Penta D25A MS Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 87

background image

29

General

* Check the engine and engine room for leaks.

* Close the fuel cock and seawater cock.

IMPORTANT!

Do not forget to open the cocks before starting the engine again.

* Read off the hour counter and carry out preventive maintenance according to the maintenance schedule.

* Turn off the main switch if the engine is not to be used for a long period.

IMPORTANT!

Never turn the power off using the main switch while the engine is running. This can

damage the alternator.

Anti-freezing measures

If the engine room cannot be protected from frost, the sea-water system must be drained and the coolant in the
fresh-water system must contain sufficient anti-freeze to prevent it from freezing. Refer to chapter Maintenance
“Seawater system” and “Freshwater system” respectively.

WARNING!

If the seawater system bursts due to freezing, it is possible for the vessel to sink.

IMPORTANT!

If the coolant does not give sufficient anti-freeze protection, it may cause costly damage

to the engine. Check the charge of the battery. A poorly charged battery can freeze and break.

Breaks in operation [not using the engine]

During periods out of service, when the boat is in the water, the engine must be run warm once a fortnight. This
will prevent the engine from corroding.

IMPORTANT!

The engine must be conserved if it is not to be used for longer than two months. Refer to

chapter Inhibiting.

After stopping

Plus d'informations sur : www.dbmoteurs.fr

«
...
27
28
29
30
31
...
»

Содержание D25A MS
























































































Отзывы:

Нет отзывов

Похожие инструкции для D25A MS

Бренд: Garmin Страницы: 14

Бренд: Navistar Страницы: 197

Бренд: Kohler Страницы: 108

Motorcycle Accessories

Бренд: S&S Cycle Страницы: 20

Бренд: TEKCELEO Страницы: 6

Бренд: Beckhoff Страницы: 31

Бренд: MTU Страницы: 163

Бренд: ZAFFER Страницы: 28

X Trainer 300 2T 2015

Бренд: Beta Motorcycles Страницы: 117

Yanmar 3TVN 88C-KHW

Бренд: HAKO Страницы: 36

Бренд: Metronic Страницы: 24

Бренд: Masport Страницы: 14

Бренд: Volvo Страницы: 20

Бренд: Volvo Страницы: 51

Бренд: Volvo Страницы: 76

Бренд: Yanmar Страницы: 214

Бренд: Honda Страницы: 48

Бренд: GMS Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды