Volvo Penta D25A MS Скачать руководство пользователя | Manualshive

Страница: 45 / 87

background image

45

Maintenance: Fuel System

Bleeding the fuel injection pump

1. Loosen the air vent cock on the fuel injection

pump about 1.5 turns.

2. Move the priming pump cap up and down to start

the flow of fuel through the system.

3. When the fuel coming out of the air vent cock

shows no visible bubbles, lock the priming pump
cap while holding it down. Then tighten the air
vent cock.

Be sure to lock the priming pump cap before tight-
ening the air vent plugs and cock. If this is not
done the cap does not return to the original posi-
tion due to the pressure in the priming pump.

4. Tighten the priming pump cap by hand until the

tightening force increases, normally this occurs
after turning it approximately 70 to 90 degrees.
Mark this position on the priming pump cap to
make item 5 work more easily.

5. Tighten the priming pump cap an additional 120

to150 degrees using a wrench.

6. Clean the engine from spoiled fuel to prevent fire

and pollution of the environment.

IMPORTANT! If the priming pump cap is tighte-

ned too much (more than 240 degrees in total),
the top of the priming pump can be damaged.

IMPORTANT! Looseness of the priming pump

cap in combination with engine vibration may
cause engine failure and damage to the installa-
tion.

Plus d'informations sur : www.dbmoteurs.fr

«
...
43
44
45
46
47
...
»

Содержание D25A MS
























































































Отзывы:

Нет отзывов

Похожие инструкции для D25A MS

VLT OneGearDrive

Бренд: Danfoss Страницы: 44

VLT OneGearDrive

Бренд: Danfoss Страницы: 21

Бренд: Danfoss Страницы: 20

Бренд: E-Z-GO Страницы: 100

Бренд: Great Wall Страницы: 72

Бренд: Westerbeke Страницы: 110

Бренд: Key Automation Страницы: 50

Command Pro EFI ECH940

Бренд: Kohler Страницы: 8

Courage PRO SV810

Бренд: Kohler Страницы: 20

KDI 3404TCR-SCR

Бренд: Kohler Страницы: 64

Бренд: Kohler Страницы: 88

Бренд: Kohler Страницы: 334

Бренд: Seg Страницы: 21

Бренд: Lycomin Страницы: 171

Бренд: Volvo Страницы: 8

Бренд: Robin America Страницы: 31

Бренд: Wren Turbines Страницы: 13

Бренд: Wren Turbines Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды