VKI Technologies CAFFE MIO Скачать руководство пользователя страница 34

Страница: 34 / 110

S E C T I O N 4 - T R O U B L E S H O O T I N G

CAFFÈ MIO – OPERATION AND SERVICE

Page 34 of 110

I n d i c a t o r M e s s a g e s

MESSAGE

POSSIBLE CAUSE

CORRECTIVE ACTION

PLEASE CHECK

WATER SOURCE

Indicates a problem with the main
water supply not getting to the
water tank.



At this point, the water tank is not

full and this message has to be
reset. To reset it, switch the power
off and on.



If the problem persists, check all

components on the water line (water
filter, tubing, fittings, etc.).



Check inlet valve to make certain it

is functioning properly.



In the case of a temporary

disruption with the water supply,
the coffee maker will reset itself
after every hour.

PLEASE CLOSE

PACKET DOOR

The packet system door is open.



Close the packet door.

PRESS

FLASHING BUTTON

A correctable fault may exist with
the equipment.



Press the flashing button to clear

this fault. Please note that the
brewer may cycle after the button is
pressed.

PROBES

CALL FOR SERVICE

The water tank may be overfilling
due to mineral build-up on water
level probes.



Clean any mineral build-up that has

accumulated on the water tank
level probes.

REPLACE FAULTY

TEMP. PROBE

The electronic temperature probe
is not working properly.



Replace the electronic temperature

probe in the water tank.

RINSE CYCLE

CHOCO. OR COFFEE

The

“

RINSE CYCLE

”

has been

activated.



Press

“

CHOCOLATE

”

to activate

whipper rinse or press

“

COFFEE

”

activate brewer rinse.



Press

“

SET

”

to exit the rinse

cycle.

SELECTION

NOT AVAILABLE

Product selected may be disabled.



Check the "

ENABLE SWITCHES

" menu

to see if product has been
canceled.

SELECT - THEN

PRESS <CUP SIZE>

Coffee maker is in "

standby

mode.



None required.

TANK IS FILLING

PLEASE WAIT

Indicates that the water tank has
not yet been filled with water.



Please wait a few minutes for the

tank to fill. If it takes too long, a
"

PLEASE CHECK WATER SOURCE

message will appear.

TO OPEN BREWER

PRESS PRODUCT

The

“

OPEN BREWER

”

menu has

been accessed.



Press

“

COFFEE

”

to open the

brewer.

TO CLOSE BREWER

PRESS START

The brewer has been opened
using the “

OPEN BREWER

” feature.



Press

“

COFFEE

”

to close the

brewer.

SELECT – THEN

INSERT COIN

The unit is in “

COIN

” mode.

This only applies if the optional
coin changer unit is installed.



Select a product and insert the

amount of money required for that
product.

PRICE: $ X.XX

CREDIT: $X.XX

The unit is in “

COIN

” mode.

This only applies if the optional
coin changer unit is installed.



The top line displays the price and the

bottom line displays how much money
has been inserted.

Содержание CAFFE MIO















































































































Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды

VKI Technologies CAFFE MIO, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды