VKI Technologies CAFFE MIO Скачать руководство пользователя страница 36

Страница: 36 / 110

S E C T I O N 4 - T R O U B L E S H O O T I N G

CAFFÈ MIO – OPERATION AND SERVICE

Page 36 of 110

T r o u b l e s h o o t i n g

Coffee Water

Short Cup Dispensed

►

Water setting may be too low – increase the water setting.

►

Water tank may not be filling quickly enough – verify main water pressure, hoses

and inlet valve.

►

Water filter may be clogged – replace water filter.

►

If a self-piercing saddle valve was used to tap into the water supply, the valve may

have an obstruction – close and open the valve.

►

Brewer may be leaking or flooding – verify the brewer operation and repair, if

necessary.

►

Outlet valve may be defective – repair or replace outlet valve

(P/N - M029082)

No Water Dispensed

►

Verify that the brewer hose is properly positioned on the diffuser.

►

Coffee valve may not be working – repair or replace the valve

(P/N - M029082)

►

Check the water pressure on the main water supply.

►

Verify that the water tank is filling properly and quickly.

►

Inlet valve may not be working properly – replace valve

(P/N – E310309S)

►

Water filter may be clogged – replace water filter.

Chocolate

Too Weak

►

Ingredient dispenser may be empty – refill the dispenser with chocolate.

►

Chocolate setting may be too low – increase the chocolate setting.

►

Water temperature setting may be too low – increase the temperature.

►

Ingredient dispenser may not be coupled properly with the motor – remove

dispenser and re-install it, making certain it is coupled with the motor.

Short Cup Dispensed

►

Water setting may be too low – increase the water setting.

►

Whipper system may be clogged. Check the whipper bowl, elbow and door tube for

any obstructions or powder accumulation.

►

Water tank may not be filling quickly enough – verify main water pressure, hoses

and inlet valve.

►

Water filter may be clogged – replace water filter.

►

If a self-piercing saddle valve was used to tap into the water supply, the valve may

have an obstruction – close and open the valve.

►

Outlet valve may be defective – repair or replace outlet valve

(P/N - M029082)

Содержание CAFFE MIO















































































































Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды

VKI Technologies CAFFE MIO, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды