VKI Technologies CAFFE MIO Скачать руководство пользователя страница 8

Страница: 8 / 110

S E C T I O N 2 - I N S T A L L A T I O N

CAFFÈ MIO – OPERATION AND SERVICE

Page 8 of 110

U n p a c k i n g

Remove the coffee maker from its shipping carton.

Lift and place the coffee maker onto your workbench.

Open the outer door (the key is in a small envelope attached to the service cord) and

open the top cover.

Remove all the shipping tape.

Shipping tape is found in the following areas: service cord, brewer spout, cup

tray.

Remove the cup tray shipped inside the coffee maker and install it onto the front door.

WARNING:

DO NOT lift the coffee maker by placing your hand underneath

the front door. It is not designed to support the weight of the machine, and
serious personal injury and/or damage to the unit may occur.

NOTE: Prior to signing for the delivery, check the shipping carton for damage. Indicate any

damage on the delivery slip and have the driver sign acknowledging it. Damages

during shipping must be claimed with the carrier, and not with VKI Technologies.

Содержание CAFFE MIO















































































































Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды

VKI Technologies CAFFE MIO, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды