VKI Technologies CAFFE MIO Скачать руководство пользователя страница 26

Страница: 26 / 110

S E C T I O N 3 - M A I N T E N A N C E

CAFFÈ MIO – OPERATION AND SERVICE

Page 26 of 110

B r e w e r A d j u s t m e n t s

Brew Chamber Installation

•

The correct removal and installation procedure for the brew chamber is crucial. Although the

assembly can be easily removed for cleaning (by lifting up the latch bar in front of the chamber),

the re-installation requires some precision. The wiper assembly on the chamber must be

inserted between the two stainless steel arms located at the rear of the brewer. These two arms

can be easily located once the brew chamber assembly is removed. Failure to properly align

the brew chamber during installation may result in excessive brewer damage.

•

When re-installing the brew chamber, make certain it is properly locked in position. Gently

grip the top of the brew chamber (not the release latch) and pull it slightly. If it is not

properly locked in place, you will be able to pull it out. Failure to lock the brew chamber in

place will result in the chamber moving forwards, and then coming down on top of the plastic

cylinder lip in front of the filter screen. This can damage the brew chamber, cylinder, the

arms and bearings and/or the vertical rod housing.

General Maintenance and Adjustments

•

Never turn the brewer backwards. This will damage the arms and bearings and possibly

the cam.

•

Use only the VKI designed screen extraction tool (illustrated below) to remove the re-

useable filter screen. The use of any other tools will damage the brewer.

•

When performing a brewer rinse, use only VKI approved powder cleaner. Any other

chemicals or detergents may damage the brewer. Do not, under any circumstances,

soak the brewer’s plastic parts in brewer cleaner for prolonged periods of time

(maximum is 30 minutes).

Lift Latch and

Pull Brew

Chamber

Содержание CAFFE MIO















































































































Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды

VKI Technologies CAFFE MIO, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды