VKI Technologies CAFFE MIO Скачать руководство пользователя страница 32

Страница: 32 / 110

S E C T I O N 4 - T R O U B L E S H O O T I N G

CAFFÈ MIO – OPERATION AND SERVICE

Page 32 of 110

I n d i c a t o r M e s s a g e s

MESSAGE

POSSIBLE CAUSE

CORRECTIVE ACTION

BEVERAGE BEING

PREPARED

Brewing cycle is in progress.



The message reverts to the

standby

message once the current

brew cycle is complete.

BREWER HOME ERR

PRESS PRODUCT

The brewer is not in the home or
starting position.



Press product button to cycle the

brewer.



The home switch may be defective

or needs to be re-adjusted or
cleaned.



An electrical connection to the

brewer home switch is faulty.



The brewer brake may not be working

properly. Adjust the brake or replace
the brewer motor.

CHECK WATER

TEMP. HARNESS

The wiring harness is not
connected to the rear board.



Connect the wiring harness to the

corresponding connector on the
rear board.

CLEAR COUNTERS

PRESS PRODUCT

The “

CLEAR COUNTERS

” menu has

been accessed.



Press

“

COFFEE

”

to enter this menu

or press

“

SET

”

to exit.

COIN CHANGER

NOT INSTALLED

The system is set to "

COIN

" mode,

but a coin changer is not installed.



Install a coin changer.



Switch to "

FREE

" mode.

DEFECTIVE COIN

CHANGER SENSOR

A sensor in the coin changer is
defective.



Replace the coin changer.

EMPTY OR INSTALL

CUP TRAY

The cup tray may not be installed,
or it may be full of liquid.



Install the cup tray.



If the cup stand is full of liquid,

empty and clean it.



The hot water valve may be

leaking. Repair or replace hot water
valve.



If the message cannot be cleared,

the rear board may be wet.
Replace the board and let the wet
one dry overnight.

EMPTY WATER TANK

OVERFLOW CUP

The water tank overflow cup may
be full of water.



Empty and clean the water tank

overflow cup.



Verify the water level probe

adjustment. They may be
positioned too high allowing too
much water into the tank.



Water level probes may need to be

cleaned.



Inlet valve may be leaking,

constantly allowing water to enter
the tank. Replace the inlet valve.



Water in the tank may be boiling.

Turn temperature down to 185-
195°F.



If message cannot be cleared, rear

board may be wet. Replace the
board and let the wet one dry
overnight.

Содержание CAFFE MIO















































































































Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды

VKI Technologies CAFFE MIO, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды