VKI Technologies CAFFE MIO Скачать руководство пользователя страница 33

Страница: 33 / 110

S E C T I O N 4 - T R O U B L E S H O O T I N G

CAFFÈ MIO – OPERATION AND SERVICE

Page 33 of 110

I n d i c a t o r M e s s a g e s

MESSAGE

POSSIBLE CAUSE

CORRECTIVE ACTION

EMPTY WATER TANK

PRESS PRODUCT

The

“

EMPTY WATER TANK

”

function

has been accessed.



To empty the water tank, press and

hold the

“

COFFEE

”

and

“

HOT

WATER

”

buttons simultaneously.

ERROR – CALL FOR

SERVICE

An error is present with the
machine.



If this message appears, the

caretaker needs to call a technician
for service.

ERROR - CHECK

STUCK BUTTON

A button on the front board is
stuck pressed down.



Fascia may be binding against the

side of a button. Re-align fascia or
trim fascia around the button(s).



A front board button may have

collapsed. Replace front board.



Machine may not be getting any

water - check and fix the water
supply. Switch machine

OFF

for ten

seconds and

ON AGAIN

ERROR DETECTED

RELOAD SOFTWARE

The software in the rear board has
been corrupted.



Using the Data Link Downloader,

re-install the software into the rear
board.

EXACT CHANGE

Equipment requires exact change
to operate.



Insert exact change or add some coins to

the coin changer tubes.

POUR PACKET

CONTENTS

The packet system has been
activated.



Pour packet contents into the packet

system and activate brew cycle.

PLEASE CHECK

BREWER

A problem exists with the brewer
motor that prevents it from finding
the home position.



Check the brewer motor home

switch.



Check the wiring to the brewer

motor.



Brewer motor may be seized. Replace

the motor.



Brewer may be jammed. Repair or

replace the brewer motor.

PLEASE CHECK

BREWER HARNESS

The wiring harness is not
connected to the rear board.



Connect the wiring harness to the

corresponding connector on the
rear board.

PLEASE CHECK

OVERFLOW HARNESS

The wiring harness is not
connected to the rear board.



Connect the wiring harness to the

corresponding connector on the
rear board.

PLEASE CHECK

TANK HARNESS

The wiring harness is not
connected to the rear board.



Connect the wiring harness to the

corresponding connector on the
rear board.

Содержание CAFFE MIO















































































































Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды

VKI Technologies CAFFE MIO, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды