VKI Technologies CAFFE MIO Скачать руководство пользователя страница 7

Страница: 7 / 110

S E C T I O N 1 - I N T R O D U C T I O N

CAFFÈ MIO – OPERATION AND SERVICE

Page 7 of 110

U s i n g C o f f e e P a c k e t s

To brew a cup of coffee using a packet, follow these simple instructions.

Press the “

PACKET

” button on the front selection panel.

Open the packet door on the top front of the machine.

Open the coffee packet and pour the contents into the packet opening on the top of the
machine.

Close the packet door.

Press the pre-selected cup size button for the packet to start the brew cycle. The LED for
this cup size will be flashing.

NOTE: To cancel the packet option if the packet button has been pressed accidentally, press

the “

COFFEE

” button. If the cycle is not started in 30 seconds, the packet cycle will

automatically be canceled.

G e n e r a l I n f o r m a t i o n



The hot water feature is “

PRESS AND HOLD

” only. Hot water will only be dispensed as long as

the “

HOT WATER

” button is pressed. It will not be dispensed “by the cup”.



There is only one button on the inner board panel. This button is used to access the set-up

mode, and to return to the main menu after a setting has been changed.



The access code to enter the SET-UP is:

“SET-UP”

ACCESS

CODE

COFFEE

PACKET

CHOCOLATE

COFFEE



To exit a sub-menu and get back to the main menu, press the

SET

button.



To display the

VEND TOTAL

, press the "

COFFEE

" and "

STRONG

" buttons simultaneously.



To display the

FREE VEND TOTAL

, press the "

CHOCOLATE

" and "

STRONG

" buttons simultaneously.



To display the

WATER TEMPERATURE

, press the "

CAFÉ MOCHA

" and "

STRONG

" buttons

simultaneously.



To reset the counters, scroll to the “

CLEAR COUNTERS

” menu in the set-up and enter the

following access code:

“CLEAR

COUNTERS”

ACCESS

CODE

COFFEE

PACKET

CHOCOLATE

COFFEE

SMALL CUP



The

COFFEE

and

SMALL CUP

buttons cannot be disabled. All other buttons can be disabled in the

ENABLE SWITCHES

menu.



This unit works in free vend only, unless an optional, side-mounted coin changer unit is

installed (p/n – A510122).

Содержание CAFFE MIO















































































































Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды

VKI Technologies CAFFE MIO, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание CAFFE MIO

Отзывы:

Похожие инструкции для CAFFE MIO

Бренды по названию

Популярные бренды