Vertex Standard VX-3R Скачать руководство пользователя

Страница: 50 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

The Emergency Automatic ID (EAI) Feature requires that you (1) store the CTCSS Tone Pair into the

Receiving Pager Memory (see page ?? for procedure), and (2) store the desired UHF coordination

frequency into Memory Channel “EAI” (see page ?? for procedure).

Selecting the EAI mode and its Transmit Time

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 31: EAI.TMR.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [TXPO] key momentarily to enable adjustment of this Set Mode Item.

4. Rotate the DIAL knob to select the desired EAI mode (Interval EAI “INT” or Continuous EAI “CON”) and

its transmit time (1-10, 15, 20, 30, 40, and 50 minutes).

5. Press the PTT switch to save the new setting and exit to normal operation.

Activating the EAI feature

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 30: EAI.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the [TXPO] key momentarily to enable adjustment of this Set Mode Item.

4. Rotate the DIAL knob to select “ON” (thus activating the EAI feature).

5. Press the PTT switch to save the new setting and exit to normal operation (with EAI feature “ON”).

When the EAI feature is activated, the “EAI” notation and the Band Number (or memory channel

number) will appear alternately in the Memory Channel Number Display Slot of the display.

To disable the EAI feature, just repeat above procedure, rotating the DIAL knob to select “OFF” in step “4”

above.

R.F. Says: The VX-3R will ignore the EAI feature when the (1) the squelch is open, (2) there is an incoming

the signal on the operating frequency, (3) the operating frequency is the same as the frequency which is

stored in the Memory Channel “EAI,” or (4) a VHF frequency is stored in Memory Channel “EAI.”

To Locate an Unresponsive Operator Using the EAI feature

1. Recall the Memory Channel “EAI” (of the searched person’s radio), which is found to next to the last

“regular” memory channel.

2. Set the CTCSS tone pair which is the same CTCSS tone pair stored in the Receiving Pager Code

Memory of the missing person’s radio.

Press and hold in the [TXPO] key for one second to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 62: PAG.CDT.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob

Vertex Standard Co., Ltd.

Содержание VX-3R






















































































Результаты поиска

Содержание VX-3R

Отзывы:

Похожие инструкции для VX-3R

Бренды по названию

Популярные бренды

Vertex Standard VX-3R, Руководство по эксплуатации

Результаты поиска

Содержание VX-3R

Отзывы:

Похожие инструкции для VX-3R

Бренды по названию

Популярные бренды