Vertex Standard VX-3R Скачать руководство пользователя

Страница: 12 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

AM:

“BARANT” (Uses the Rubber Flex Antenna) or “BAREXT” (Uses both the internal Bar Antenna

and the Rubber Flex Antenna).

FM:

“EXTANT” (Uses the Rubber Flex Antenna) or “EARPHO” (Uses the Earphone Antenna).

5. When finish the selection, press the [RADIO] key momentarily to exit from the antenna selection mode.

6. Press the [RADIO] key momentarily again to exit from the AM and FM Broadcast Reception mode and

return to normal operation.

R.F. Says: If you wish to output the audio of the FM Broadcast station to the VX-3R internal speaker using

with an earphone antenna, select Set Mode Item 77: SP OUT to “SPKR”.

SUB-RX Operation

The SUB-RX Operation allows you to monitor your desired amateur band frequency while receiving AM or

FM broadcast stations. Furthermore, you may transmit on the amateur frequency by pressing the PTT

switch.

When a signal is received in the amateur band, the audio is output instead of the AM or FM Broadcast

station. When the amateur band signal drops, the SUB-RX Operation is resumed determine from the user

setting.

1. Set the VX-3R to the desired amateur band frequency by the VFO or Memory channel selection.

2. Press the [F/W] key then press the [RADIO] key.

3. Rotate the DIAL knob to select the resume mode of the AF Priority feature. Available selections are:

TX 1S - TX 10S: When passes the selected time after the transmission was over on the amateur band,

the AM or FM Broadcast station will be heard from the speaker and the SUB-RX Operation is resumed.

However, when the signal received in the amateur band, the SUB-RX Operation will halt on the

amateur band frequency (the SUB-RX Operation does not resume.)

TRX 1S - TRX 10S: When passes the selected time after the amateur band signal drops or

transmission was over, the AM or FM Broadcast station will be heard from the speaker and the

SUB-RX Operation is resumed.

HOLD: When the signal received in the amateur band or transmit on the amateur band, the SUB-RX

Operation will halt on the amateur band frequency (the SUB-RX Operation does not resume.). You

must manually re-initiate the SUB-RX Operation, if you wish to resume.

OFF: Disable the SUB-RX Operation.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

4. Press the [RADIO] key to activate the SUB-RX Operation. The “PRI” icon appears at the above of the

volume level indicator on the display.

5. Press the [BAND] key to toggle the receiving band between “AM broadcast” and “FM broadcast”.

6. Rotate the DIAL knob to select the desired Broadcast station.

7. When the signal received in the amateur band, the amateur band audio output to the speaker instead

Vertex Standard Co., Ltd.

Содержание VX-3R






















































































Результаты поиска

Содержание VX-3R

Отзывы:

Похожие инструкции для VX-3R

Бренды по названию

Популярные бренды

Vertex Standard VX-3R, Руководство по эксплуатации

Результаты поиска

Содержание VX-3R

Отзывы:

Похожие инструкции для VX-3R

Бренды по названию

Популярные бренды