Vertex Standard VX-3R Скачать руководство пользователя страница 37

Страница: 37 / 85

FCC ID: K6620285X20

IC ID: 511B-20285X20

VX-3R Operating Manual

±1 MHz, ±2 MHz, ±5 MHz: The scanner will sweep frequencies within the selected bandwidth.

BAND: The scanner will sweep frequencies only on the current band.

ALL: The scanner will sweep all frequencies between 0.5 MHz and 999 MHz.

PMS-X: The scanner will sweep frequencies within the currently-selected PMS frequency pair. See

page ?? for details.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Release the [BAND] key to start scanning.

4. If and when the scanner encounters a signal strong enough to open the squelch, the scanner will halt

temporarily; the decimal point of the frequency display will blink during this “Pause” condition.

5. The scanner will then resume according to the Scan-Resume mode selected in the previous section.

6. To cancel scanning, press the PTT switch or [V/M] key.

R.F. Says: 1) When you start scanning, the VX-3R will be changing frequency in the upward direction. If you

want to change direction of the scan while it is underway, rotate the DIAL knob one click in the opposite

direction (in this case, one click counter-clockwise). You’ll see the scanner turn around and change

frequency downward!

2) You may change the scanner’s method of operation so that the VFO frequency will jump to the low band

edge of the

band when the VFO frequency reaches the high edge of the

current

band (or vice versa).

See page ?? regarding Set Mode Item 90: VFO MD.

Setting the Squelch Level during active Scanning operation

The VX-3R allows adjustment of the Squelch level “on the fly” while you are scanning.

1. While the scanner is engaged, press the [F/W] key, then press the MONI key (the current squelch level

will appear below the frequency display).

2. Rotate the DIAL to select the desired Squelch level.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. Press the PTT switch momentarily to save the new setting and exit to normal operation. In this case,

pressing the PTT switch this one time will not causing scanning to stop.

How to Skip (Omit) a Frequency during VFO Scan

If the VFO scan stops on a frequency or frequencies that you do not need (such as a spurious radiation

from a television), such frequencies can be “skipped” during VFO scanning. This accomplished by storing

these frequencies in a special “Frequency Skip Memory” bank reserved for this purpose.

To skip a frequency during VFO scanning:

1. While VFO scanning is stopped on the frequency that you do not need, press and hold the [F/W] key

for 1/2 seconds, then rotate the DIAL knob to select the desired Frequency Skip Memory channel (901

Vertex Standard Co., Ltd.

Содержание VX-3R






















































































Результаты поиска

Содержание VX-3R

Отзывы:

Бренды по названию

Популярные бренды

Vertex Standard VX-3R, Руководство по эксплуатации

Результаты поиска

Содержание VX-3R

Отзывы:

Бренды по названию

Популярные бренды