Vermont Castings 33CFDVNI Скачать руководство пользователя страница 57

Страница: 57 / 68

CFDV Series Gas Fireplace

20306739

OPTIONAL ACCESSORIES

ALL PILOT/CONTROL SYSTEMS

OPTIONAL ACCESSORIES

There are a variety optional accessories available for
the CFDV Direct Vent Fireplace. Porcelain panels are

available as an alternative to the firebrick provided with
your fireplace. The porcelain panels can give your fireplace

a smooth contemporary look and feel.
The Contemporary Stone and Glass Kit includes a set

of ceramic fiber stones and fireglass and can be used
to alter your fireplace from a rustic look to a minimalist
appearance. Additional crushed fireglass is available in a

variety of colors.
There is also a choice of two optional fans. The BLOT fan

utilizes a thermostat for blower operation. The FK12 fan

is also available. A speed control is available to regulate
fan speed.

Porcelain Panel Kit (33CFDV)

PL33CFDVB

Porcelain Panel Kit (36CFDV)

PL36CFDVB

Porcelain Panel Kit (42CFDV)

PL42CFDVB

Contemporary Stone and Glass Kit

CKCFDV

Crushed Fireglass Kits:

Glass Kit Bronze

GKB

Glass Kit Diamond

GKD

Glass Kit Onyx

GKO

Glass Kit Sapphire

GKS

Blower Kits:

T-Stat Blower w/ Speed Control

BLOT

Manual Blower

FK12

Speed Control for FK12

26D0746

SYMPTOM

POSSIBLE CAUSE

ACTION

The pilot and main burner

extinguish while in operation

Inner vent pipe leaiking exhaust

gasses back into system

Check for product leak. Replace defective

pipe section.

Horizontal vent improperly pitched.

Check that horizontal venting pipe is

running upward

⁄

" per foot. Do not run the

pipe level or downward.

Improper vent cap intallation

Check for proper installation and that cap

is clear of debris or blockage.

Glass soots

Flame impingement on logs

Install log set per the instructions. Inspect

the injector and air intake area. Make sure

this area does not have any blockage from

debris and clean. Check gas supply.

Flame burns blue and lifts off

burner (ghosting)

Insufficient fresh air being supplied

Check:

1. That the vent cap is installed properly

and free of debris.

2. That the vent system joints are tight and

have no leaks.

3. That no debris is blocking the inner

air intake at the bottom back of the

combustion chamber.

4. That the glass is properly secured and

latched.

Содержание 33CFDVNI





































































Результаты поиска

Содержание 33CFDVNI

Отзывы:

Похожие инструкции для 33CFDVNI

Бренды по названию

Популярные бренды

Vermont Castings 33CFDVNI, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 33CFDVNI

Отзывы:

Похожие инструкции для 33CFDVNI

Бренды по названию

Популярные бренды