Vermont Castings 33CFDVNI Скачать руководство пользователя страница 4

Страница: 4 / 68

CFDV Series Gas Fireplace

20306739

IMPORTANT SAFETY INFORMATION

11. Do not modify fireplace under any circumstances. Any

parts removed for servicing must be replaced prior to

operating fireplace.

12. Turn fireplace off and let cool before servicing, install

ing, or repairing. Only a qualified service person should

install, service, or repair the fireplace. Have burner

system inspected annually by a qualified service

person.

13. You must keep control compartments, burners, and

circulating air passages clean. More frequent cleaning

may be needed due to excessive lint and dust. Turn off

the gas valve and pilot light before cleaning fireplace.

14. Have venting system inspected annually by a quali-

fied service person. If needed, have venting system

cleaned or repaired. Refer to

Cleaning and Mainte-

nance

section of this manual.

15. Keep the area around your fireplace clear of combus

tible materials, gasoline, and other flammable vapor

and liquids. Do not run fireplace where these are used

or stored. Do not place items such as clothing or deco-

rations on or around fireplace.

16. Do not use this fireplace to cook food or burn paper or

other objects.

17. Never place anything on top of fireplace.

18. Do not use any solid fuels (wood, coal, paper, card-

board, etc.) in this fireplace. Use only the gas type

indicated on rating plate.

19. This appliance, when installed, must be electrically

grounded in accordance with local codes or in the

absence of local codes, with the

National Electrical

Code, ANSI/NFPA 70

, or the

Canadian Electrical Code,

CSA C22.1.

20. Do not obstruct the flow of combustion and ventilation

air in any way. Provide adequate clearances around

air openings into the combustion chamber along with

adequate accessibility clearance for servicing and

proper operation.

21. Do not use fireplace if any part has been under water.

Immediately call a qualified service technician to

inspect the appliance and to replace any part of the

control system and any gas control which has been

under water.

22. Do not operate fireplace if any log is broken.

23. Do not use a blower insert, heat exchanger insert, or

any other accessory not approved for use with this

fireplace.

24. Do not operate appliance with the glass front

removed, cracked, or broken. Replacement of the

glass should be done by a licensed qualified ser

vice person.

IMPORTANT:

PLEASE READ THE FOLLOWING

CAREFULLY

It is normal for fireplaces fabricated of steel

to give off some expansion and/or contraction

noises during the start up or cool down cycle.

Similar noises are found with your furnace heat

exchanger or car engine.

IMPORTANT:

PLEASE READ THE FOLLOWING

CAREFULLY

It is not unusual for gas fireplace to give off some

odor the first time it is burned. This is due to the

manufacturing process.

Please ensure that your room is well ventilated

during burn off — open all windows.

It is recommended that you burn your fireplace

for at least ten (10) hours the first time you use it.

Place the fan switch in the “OFF” position during

this time.

CODE APPROVAL

Direct Vent type appliances draw all combustion air from

outside of the dwelling through the vent pipe.
These appliances have been tested by CSA and found to

comply with the established standards for DIRECT VENT

GAS FIREPLACE HEATERS in the USA and Canada as

follows:

LISTED VENTED GAS FIREPLACE HEATER

TESTED TO:

ANSI Z21.88-2015/CSA 2.33-2015 STANDARDS

The installation must conform with local codes or, in the

absence of local codes, with the

National Fuel Gas Code,

ANSI Z223.1/NFPA 54

, or the

National Gas and Propane

Installation Code, CSA B149.1

A manufactured home (USA only) or mobile home OEM

installation must conform with the

Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

or when such a standard is not applicable, the

Standard for

Manufactured Home Installations, ANSI/NCSBCS A225.1

Standard for Gas Equipped Recreational Vehicles and

Mobile Housing, CSA Z240.4

Never connect unit to private (non-utility) gas wells. This

gas is commonly known as wellhead gas.

WARNING

Содержание 33CFDVNI





































































Результаты поиска

Содержание 33CFDVNI

Отзывы:

Похожие инструкции для 33CFDVNI

Бренды по названию

Популярные бренды

Vermont Castings 33CFDVNI, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 33CFDVNI

Отзывы:

Похожие инструкции для 33CFDVNI

Бренды по названию

Популярные бренды