Vermont Castings 33CFDVNI Скачать руководство пользователя страница 11

Страница: 11 / 68

CFDV Series Gas Fireplace

20306739

VENTING INSTALLATION

OPTIONAL TOP VENT APPLICATION

The appliance is shipped as a rear vent unit. If the installa-

tion layout requires the unit to be a top vent configuration

the appliance can be converted by following the steps

below.

When removing and refitting the plates be sure the

associated gaskets are undamaged and refitted as

required.

1. Remove the rear plate by removing one (1) screw. Set

aside.

Figure 11

2. Remove the plate with the 7" collar and gasket by re-

moving eight (8) screws. Set aside.

Figure 12

FP3022
remove 7 collar

Remove

Screws

Remove

Screws

7" Collar

FP3022

Figure 12 –

Remove 7" Collar and Gasket

3. Remove the plate with the 4" collar and gasket by re-

moving four (4) screws. Set aside.

Figure 13

4. Remove the top plate located on top of the unit by re-

moving one (1) screw. Set aside.

Figure 13

Figure 13 –

Remove 4" Collar and Gasket and Top Plate

FP3023
remove 4 collar

Remove

Screws

Remove

Screws

4" Collar

FP3023

Remove

Screw

Top Plate

5. Remove one (1) screw to remove the inner top plate

located on top directly beneath the plate just removed.

Break away the 7" circle using a screwdriver and rein-

stall.

Figure 14

Figure 14 –

Remove Circle Section from Inner Top Plate

FP3024
remove circle

Remove Circle

FP3024

FP3025
Inner top plate

Inner Top Plate

FP3025

FP3021
remove rear plate

Screw

Rear Plate

FP3021

Figure 11 –

Remove Rear Plate

Содержание 33CFDVNI





































































Результаты поиска

Содержание 33CFDVNI

Отзывы:

Похожие инструкции для 33CFDVNI

Бренды по названию

Популярные бренды

Vermont Castings 33CFDVNI, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 33CFDVNI

Отзывы:

Похожие инструкции для 33CFDVNI

Бренды по названию

Популярные бренды