Vermont Castings 33CFDVNI Скачать руководство пользователя страница 35

Страница: 35 / 68

CFDV Series Gas Fireplace

20306739

ELECTRICAL INSTALLATION – MILLIVOLT

Figure 68 –

Millivolt Gas Pressure Check at Gas Valve

FP1979
Millivolt gas valve

FP1979

Pressure

Test “IN”

Pressure

Test “OUT”

HI/LO Knob

Pilot Adjustment Screw

ELECTRICAL WIRING

This fireplace will work without any electrical supply.

Electricity is only needed to operate blower.

NOTE:

If installed in mobile home, fireplace must be bolted

securely to floor

CAUTION

Label all wires before disconnecting when

servicing controls. Wiring errors can cause

improper and dangerous operation.

Electrical connections should only be performed by

a qualified, licensed electrician. Main power must

be off when connecting to main electrical power

supply or performing service. All wiring shall be

in compliance with all local, city and state codes.

The appliance, when installed, must be electrically

grounded in accordance with local codes or in the

absence of local codes, with the National Electrical

Code ANSI/NFPA 70 (latest edition) and Canadian

Electrical Code, CSA C22.1.

WARNING

4. To adjust flame height, turn HI/LO knob to HI to get

maximum pressure to burner. Turn HI/LO knob to LO

to get minimum pressure.

5. To check gas pressures at valve, turn captured screw

counter clockwise 2 or 3 turns and then place tubing

to pressure gauge over test point. Turn unit to high.

Figure 68.

After taking pressure reading, be sure and

turn captured screw clockwise firmly to reseal. Do not

over torque. Check test points for gas leaks.

Figure 69 –

Junction Box Wiring Diagram

FP1912
Junction box wiring
8/08

Junction Box

Factory Supplied

Not Supplied

120V AC

60Hz

JUNCTION BOX WIRING

1. This should be done before framing the fireplace. Wire

the receptacle into an electrical circuit. Wire with mini-

mum 60° C wire in accordance with prevailing codes.

2. Remove the external junction box cover by removing

the screw from the side of the outside firebox wall.

Junction box was installed at the factory.

3. The junction box cover has a factory installed “romex”

style strain relief connector. After connecting the wires,

route the wire leads through this connector.

Figure 69

Verify proper operation after servicing.

Содержание 33CFDVNI





































































Результаты поиска

Содержание 33CFDVNI

Отзывы:

Похожие инструкции для 33CFDVNI

Бренды по названию

Популярные бренды

Vermont Castings 33CFDVNI, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 33CFDVNI

Отзывы:

Похожие инструкции для 33CFDVNI

Бренды по названию

Популярные бренды