Vermont Castings 33CFDVNI Скачать руководство пользователя страница 49

Страница: 49 / 68

Figure 81 –

Porcelain liner installation

Figure 82 –

Firebrick liner installation

CFDV Series Gas Fireplace

20306739

KT1892
porcelain panels

Top Flange

Left Panel

Rear Panel

Right Panel

KT1892

FINAL INSTALLATION

ROCK WOOL PLACEMENT

1. Your fireplace is supplied with three (3) 8-gram bags

of rock wool embers: Use one (1) 8 gram bag of rock

wool for propane/LP models and up to three (3) bags

of rock wool for natural gas models depending on the

size of your fireplace.

2. For best results in flame appearance and operation, pull

the rock wool apart into dime-sized pieces or smaller.

Cover the entire ported surface of the burner with one

thin layer of rock wool.

Figure 83

3. Place the logs on the burner. Refer to the “Log Place-

ment Section.” Light the unit and after 15 minutes check

burner flame and glow. Adjust embers as necessary to

achieve an even and clean flame.

KT1893
firebrick

Retainer

Bracket

Left Panel

Rear Panel

Right Panel

KT1893

INSTALLING BRICK LINER KIT
Kit contents:

• One (1) Right panel

• One (1) Left panel

• One (1) Rear panel

• Two (2) Self-drilling #8 screws

• Two (2), Retainer brackets

1. Remove the canopy, safety barrier, glass door frame

and log set (if applicable) .

2. Remove the top heat shield.

3. Install the center firebrick panel on the back wall first.

Stand firebrick panel straight up against the back of

fireplace with the bottom edge at bottom of inner firebox.

4. Repeat Step 3 with the left and right side firebrick pan

els. Secure the top of each side firebrick panel to the

fireplace with one retainer bracket and one screw.

5. Use a screw gun to drive in the self-drilling screw into

the sheet metal through the hole in the retainer bracket.

6. Re-install top heat shield.
7. Re-install log set, glass door, safety barrier and canopy.

FP3016
36CFDV rockwool placement

Rock Wool Area

FP3016

Содержание 33CFDVNI





































































Результаты поиска

Содержание 33CFDVNI

Отзывы:

Похожие инструкции для 33CFDVNI

Бренды по названию

Популярные бренды

Vermont Castings 33CFDVNI, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 33CFDVNI

Отзывы:

Похожие инструкции для 33CFDVNI

Бренды по названию

Популярные бренды