VERDER CARBOLITE GERO 3016 Скачать руководство пользователя страница 35

Страница: 35 / 56

rate prior to the power outage.

Rset

- The program will be reset.

CONt

- The program will continue to run from the point at

which it was interrupted.

R.RESN

Ramp Rate
Resolution

Used to set the display resolution of segment ramp rate
parameters when read/written via scaled integer comms.

nnnnn

- No decimal places

nnnn.n

- One decimal place (default)

nnn.nn

- Two decimal places

nn.nnn

- Three decimal places

n.nnnn

- Four decimal places

RESN

Program
Resolution

Used to set the time resolution of the segment time left and
the program time left.

SeC

- Seconds

mIN

- Minutes

HOur

- Hours

P.Set

List

- (See section 6.3 for details on the Program Setup List)

ALm

List

INST

Alarm Number

Used to select the alarm whose parameters you wish to
edit. There are 6 alarms available.

Note:

Also adjustable at Operator Level 3.

Type

Displays the alarm type (see section 7.0)

stat

Alarm Status

Displays the status of the alarm.

Off

- The alarm is off

ACT

- The alarm is active, but has been acknowledged.

INA

- The alarm is active and the conditions that

triggered the alarm have passed, however the alarm
has not been acknowledged

ANA

- The alarm is still active and has not been acknow-

ledged

Input

Displays the value being monitored by the alarm.

THLD

Threshold

Only available if an "Absolute High" or "Absolute Low" alarm
has been configured. The desired alarm type must be
specified at the time of order.
Used to set the temperature threshold that will determine
when an alarm relay will activate for High (

Abs.H

)or Low

(

Abs.L

) alarms.

Содержание CARBOLITE GERO 3016

























































Результаты поиска

Содержание CARBOLITE GERO 3016

Отзывы:

Бренды по названию

Популярные бренды

VERDER CARBOLITE GERO 3016, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CARBOLITE GERO 3016

Отзывы:

Бренды по названию

Популярные бренды