manualshive.com logo in svg

VERDER CARBOLITE GERO 3016, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
VERDER CARBOLITE GERO 3016 Скачать руководство пользователя страница 5

1.2

Technical Terms

Due to the complex nature of temperature control, this manual uses technical terms.

Here is a list of some of the terms used within this manual, alongside their explanation:

Term

Description

Setpoint

The target temperature the furnace or oven is trying to reach (°C)

Over-
Temperature
Protection

A system to prevent the product or process being damaged if the
temperature has increased above a temperature specified by the user
(over-temperature setpoint). Power to the heating elements is stopped
until either the temperature of the product drops below the over-
temperature setpoint, or the user manually increases the over-
temperature setpoint

Over-
Temperature
Setpoint

The temperature at which the over-temperature protection system
triggers

Heating
element

The electrically powered heating device used within the product
(furnace or oven)

Thermocouple A thermoelectric device for measuring temperature

PID

Proportional Integral Derivative - the mathematical control system
used by the controller

Program

A series of instructions that tell the controller how to behave. A
program is divided into sections called "segments"

Segment

A section of a program. A program can have 24 individual segments.
There are 6 different segment types that can be configured. The
segments define how the controller behaves when a program reaches
that segment.The last segment of a program must always be an "End"
type

Holdback

Used when running a program. Holdback is the amount (in °C /°F / K)
by which the programmed setpoint can run ahead of the actual
measured temperature before holdback operates and prevents the
program from progressing until the actual temperature catches up.
This can be applied to either heating, cooling or both, depending on the
"Holdback Type" set by the user

Ramp Rate

The amount of degrees (°C /°F / K) the temperature should increase
per second, minute or hour (dependant on "Ramp Units")

Ramp Units

Used to define whether the temperature should increase at

X

°C per

second,

X

°C per minute or

X

°C per hour

5

Содержание CARBOLITE GERO 3016

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды