VERDER CARBOLITE GERO 3016 Скачать руководство пользователя страница 21

Страница: 21 / 56

If you have ordered the 3016 with multiple event outputs, please make a note of what
the event output function is. This is for your own future reference:

Event Output 1

Event Output 2

Event Output 3

Event Output 4

Event Output 5

Event Output 6

Event Output 7

Event Output 8

6.5

Program Example

Note:

This program example is for a high-temperature furnace product. For products

with lower maximum temperatures, such as ovens, lower temperature values should
be used.

1. Log in at Operator Level 2.
2. From the home display, press the page button until

P.Set

appears.

3. Press the scroll button until

HB.TYP

appears.

4. Press the up and down buttons to select

OFF

, then press the scroll button.

5. Press the up and down buttons until the

RAMP.U

value reads

P.mIN

, then press the

scroll button.

6. Press the up and down buttons until the

DWEL.U

value reads

mINS

, then press the

scroll button

P.END

appears.

7. Press the up and down arrows to select

RSEt

8. Press the scroll button to access values for segment 1.
9. Press the scroll button until

S.TYPE

appears.

10. Press the up and down buttons until

RAte

appears, then press the scroll button.

11. Press the up and down buttons until the

TSP

reads

400°C

then press the scroll but-

ton.

12. Press the up and down buttons to adjust the

R.RATE

until it reads

5.0°C

, then press

the scroll button.

13. Press the scroll button to access values for segment 2.
14. Press the scroll button until

S.TYPE

appears.

15. Press the up and down buttons until

dWEL

appears, then press the scroll button.

16. Press the up and down buttons until the

DUR

value reads

00:30

, then press he scroll

button.

17. Press the scroll button to access values for segment 3.
18. Press the scroll button until

S.TYPE

appears.

19. Press the up and down buttons until the

TSP

reads

600°C

then press the scroll but-

ton.

20. Press the scroll button to access values for segment 4.

Содержание CARBOLITE GERO 3016

























































Результаты поиска

Содержание CARBOLITE GERO 3016

Отзывы:

Бренды по названию

Популярные бренды

VERDER CARBOLITE GERO 3016, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CARBOLITE GERO 3016

Отзывы:

Бренды по названию

Популярные бренды