VERDER CARBOLITE GERO 3016 Скачать руководство пользователя страница 37

Страница: 37 / 56

Deviation High

- The alarm relay will activate if the

temperature rises above the sum of the Reference and
Deviation values [

REF

DEV

], and will remain activated

until the temperature drops below the sum of the Refer-
ence and Deviation values minus any Hysteresis value
set [

REF

DEV

HYST

]

Deviation Low

- The alarm relay will activate if the

temperature drops below the sum of the Reference and
Deviation values [

REF

DEV

], and will remain activated

until the temperature rises above the sum of the Refer-
ence and Deviation values plus any Hysteresis value set
[

REF

DEV

HYST

]

Deviation Band

- The alarm relay will activate if the

temperature deviates above or below the Reference
value plus or minus the Deviation value [

REF

DEV

], and

will remain activated until the temperature returns
within the deviation band, plus or minus any Hysteresis
value set [

REF

DEV

HYST

] (e.g. if the target setpoint

is 500°C, the alarm relay will activate if the tem-
perature is outside the range of 450°C and 550°C, and
deactivate when the temperature is between 450°C
and 550°C)

Note:

Also adjustable at Operator Level 3.

Comm

List

s.list

Sublist

Use the up and down arrows to view sublists of additional
parameters. Use the scroll button to select a sublist.

MaIN

- Access parameters relating to Main Sublist

Nwrk

- Access parameters relating to Network Sublist

mAin

Sublist:

intf

Interface

Displays the type of connection interface.

EtH

- Ethernet

r485

- RS485

n.sta

Status

Displays the status of communications used by Modbus TCP.

OFFL

- Offline and not communicating

INIt

- Initialising communications

RdY

- Ready to accept connection. Not used by Modbus

TCP.

Run

- Ready to accept connections or controller com-

municating

w.time

Watchdog Time

If the communications stop addressing the instrument
longer than this configurable period, the Watchdog Flag will
become active.

Содержание CARBOLITE GERO 3016

























































Результаты поиска

Содержание CARBOLITE GERO 3016

Отзывы:

Бренды по названию

Популярные бренды

VERDER CARBOLITE GERO 3016, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CARBOLITE GERO 3016

Отзывы:

Бренды по названию

Популярные бренды