VERDER CARBOLITE GERO 3016 Скачать руководство пользователя страница 32

Страница: 32 / 56

TGT.sp

Target Setpoint

Used to adjust the setpoint temperature.

Note:

Also adjustable at Operator Level 3.

w.sp

Working
Setpoint

Displays the current working setpoint.

w.out

Working Output

Displays the current power output in %.

AtuN

Sublist:

Tune

Autotune Enable

Used to enable or disable an autotune.

- Autotune is enabled

Off

- Autotune is disabled

Note:

Also adjustable at Operator Level 3.

T.HI

Autotune
Maximum
Output

Used to set a maximum output limit during tuning.

The default value is

100

Note:

Also adjustable at Operator Level 3.

T.LO

Autotune
Minimum Output

Used to set a minimum output limit during tuning.

The default value is

-100

Note:

Also adjustable at Operator Level 3.

T.STAT

Autotune Status

Displays the current status of the autotune.

Off

- Autotune is unavailable.

Rdy

- The controller is ready to run an autotune

triG

- An autotune has been triggered to run, but is

waiting for another process to complete before run-
ning.

Run

- The autotune function is running.

donE

- The autotune completed successfully and tun-

eset parameters have been updated.

Abor

- The autotune has been aborted.

tOut

- If the autotune sequence exceeds two hours in

duration, it will timeout and be aborted.

OFLw

- A buffer overflow occurred while collecting pro-

cessing data. Contact Carbolite Gero Service for sup-
port.

STAGE

Stage of
Autotune

IdLe

- Not autotuning.

moni

- The process is being monitored. This stage lasts

one minute and the setpoint can be adjusted during this
time.

Init

- An initial oscillation is being established.

- Maximum output applied.

Содержание CARBOLITE GERO 3016

























































Результаты поиска

Содержание CARBOLITE GERO 3016

Отзывы:

Бренды по названию

Популярные бренды

VERDER CARBOLITE GERO 3016, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CARBOLITE GERO 3016

Отзывы:

Бренды по названию

Популярные бренды