VERDER CARBOLITE GERO 3016 Скачать руководство пользователя страница 15

Страница: 15 / 56

P.NAME

Program
Name

Displays the name of the program. This parameter is read
only.

P.CUR

Current
Program
Number

Displays the number of the program currently running. This
parameter is read only.

C.NAME

Current
Program
Name

Displays the name of the program currently running. This
parameter is read only.

P.MODE

Program
Mode

Displays the status of the current program. Can be
adjusted using the up and down buttons:

RUN

- The program is running.

HOLd

- The program is paused.

Reset

- The program is stopped.

P.SP

Program
Setpoint

Displays the setpoint of the current program. This
parameter is read only.

P.TIM.L

Program
Time Left

Displays the amount of time left until the program
completes. This parameter is read only.

Note:

The display will show a maximum time of 500

hours, however some programs may exceed this length
of time. The value displayed does not take into account
the effect of holdback within a program.

P.CYC.L

Program
Cycles Left

Displays the amount of program cycles left to run. This
parameter is read only.

S.NUM

Segment
Number

Displays the number of the current program segment. This
parameter is read only.

S.NAME

Segment
Name

Displays the name of the current program segment.
This parameter is read only.

S.TYPE

Segment
Type

Displays the segment type of the current program segment.
This parameter is read only.

S.TIM.L

Segment
Time Left

Displays the amount of time left until the current segment
completes. This parameter is read only.

TSP

Target
Setpoint

Displays the target setpoint of the current segment. This
parameter is read only.

Note:

Only displayed if the current segment type is

RAtE

tImE

, or

StEP

R.Rate

Ramp Rate

Displays the current ramp rate of the segment.

Note:

Only displayed if the current segment type is

RAtE

tImE

, or

StEP

EVT.1 /

evt.2

Event 1 /

Displays whether any event outputs or alarms are on or off.

Содержание CARBOLITE GERO 3016

























































Результаты поиска

Содержание CARBOLITE GERO 3016

Отзывы:

Бренды по названию

Популярные бренды

VERDER CARBOLITE GERO 3016, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CARBOLITE GERO 3016

Отзывы:

Бренды по названию

Популярные бренды