Velocity MMP Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 84

Velocity MMP Скачать руководство пользователя страница 56

Velocity Operation Manual

www.velocitydetection.com

56

When global relays have been disabled, the LCD display
changes from SYSTEM NORMAL to Disablement, as
shown.

The screen shows the number of relay output interfaces
disabled.

The General Disablement LED will be lit.

Details of the disabled relay outputs can be viewed by

pressing the disabled loop devices icon

or the

disabled local I/O icon

. If any zones have all of their

outputs disabled, it will be indicated by the disabled zone

outputs icon

.

To re-enable the relay status, press the ‘Enabled’
selection area. The text will change from ‘All disabled’ to
‘All Enabled’ for relay status.

Press the exit icon

. The panel will ask if you want to

save the changes.

Press tick

to save the changes, or press

to

discard.

Change the global mode for sounder status to disable by
pressing the ‘Disabled’ selection area. The text will
change from ‘All enabled’ to ‘All disabled’ for sounder
status.

This will disable

ALL

panel sounder output interfaces.

Press the exit icon

. The panel will ask if you want to

save the changes.

Press tick

to save the changes, or press

to

discard.

When sounder status has been disabled, the LCD display
changes from SYSTEM NORMAL to Disablement. The
screen shows:-

The number of disabled SLC sounder devices.
The number of disabled NAC outputs.
The General Disablement and NAC Disablement LED will
be lit

If there are any output relays on the system that are not
disabled, the Disabled Alarm Group icon will not be
displayed.

If there are no relays fitted, or if the relays have been
disabled as well , the Disabled Alarm Group icon will be
displayed

«
...
54
55
56
57
58
...
»

Содержание MMP





















































































Отзывы:

Нет отзывов