Veeder-Root TLS-450PLUS, Руководство оператора

Страница: 24 / 69

Initial Setup Of The Console Using Workflow Wizard Setup>Devices
20
Setup>Devices - Continued
PROBE SETUP
Set up each probe being m onitored before selecting the next device type.
Configured
Touch the radio button to enable or disable configuration of the selected
probe.
NOTES:
•
Do not enable probe configuration until its address is assigned!
• Once enabled, do not disable a probe if it is assigned to a tank. You m ust
first unassign the probe fro m the tank before the probe can be disabled.
(see Setup > Tank > General).
Address
Touch and select the address of this probe.
Label
Touch to enter a description of this probe (up to 20 alphanu m eric characters)
that will appear on the console screens and in reports.
Serial Number
[Read Only] Console auto-detected serial nu m ber of this device.
Type
[Read Only] Console auto-detected type of this device.
Float Type
Installed Mag probe float type (the console will display only the applicable
float size options for this device). For exa
m ple, depending on the probe
installed the float sizes below could display in the drop down list:
NOTES:
• Only circuit codes D004, D005 and D006 are allowed to set the float type to
4.0 in phase separation.
• If the probe is changed and the previous float is supported by the new
probe, the float assign m ent will re m ain the sa m e. Otherwise the default
float will be assigned to the new probe.
• Only select
Custom
if the literature that was shipped with probe float kit
specifically states that you m ust choose this Float Type. Currently only
three m ag probes use Custo m Float Types: Che m -ISO m ag probes, LPG-ISO
m ag probes and the Mag-FLEX probe with low level water floats.
When
Custom
float type is selected, the Fuel Offset, Water Offset, Water
Mini m u m and Invalid Fuel para m eter fields below are enabled for edit.
Refer to the appropriate installation kit m anual for these entries (see
“Related Docu m ents” on page 1).
Fuel Offset -
Touch to enter the Fuel Offset value listed in the appropriate
kit m anual (577013-770, 577013-773 or 577014-056).
Water Offset
(Mag-FLEX probes with Low Level Water Float only) -
Touch to enter the Water Offset value listed in the 577014-056 m anual.
Water Minimum
(Mag-FLEX probes with Low Level Water Float only) -
Touch to enter the Water Mini m u m value listed in the 577014-056 m anual.
Invalid Fuel -
Touch to enter the Invalid Fuel value listed in the appropri-
ate kit m anual (577013-770, 577013-773 or 577014-056).
Density Code
This field stores specifications for a density probe. It m ust be exactly 14
characters, and is co m posed of four parts as described below:
The density code has the following for m at: FGGGGGGMMMMDDD, e.g.,
B7053686719512, and is i m pressed in the float body (see i m age below).
Where:
F = Fuel Type: A for gasoline and B for diesel.
Using the exa m ple density code above: B = Diesel,
G
= Gauss
The last two digits are the gauss readings for each m agnet in the den-
sity float. The prefix is always 7 and is o m itted fro m the density code.
Using the exa m ple density code above:
70 Gauss = 77.0 for top m agnet in gra m s
53 Gauss = 75.3 for m iddle m agnet in gra m s
68 Gauss = 76.8 for botto m m agnet in gra m s
M = Mass
The last four digits of the m ass of the float. The prefix is always 1 and is
o m itted fro m the density code.
Using the exa m ple density code above:
6719 = Mass of 16.719 gra m s
D
= Density of the float
The prefix is dependent on the fuel type and is o m itted fro m the density
code. A = 7 (gasoline) and B = 8 (diesel).
Using the exa m ple density code above:
512 = density of 851.2 kg/ m
3
for a fuel type of diesel.
NOTE: If you change the Density Code, the Density Offset History is
cleared and current Density Offset is set to zero. See Diagnostics>
Probe>Density Offset screen for details on console density values.
Density Float Serial Number
Touch this field to enter the density float’s serial nu m ber.
NOTE: if you change the density float serial nu m ber, the Density Offset
History is cleared and the current Density Offset is reset to zero.
The density float serial nu
m ber has the following for m at - yywwxxxx,
e.g., 13240161, and is i m pressed in the float body (see i m age below).
Where;
YY
= the last two digits of the year it was m anufactured’
WW
= the nu m ber of the week it was m anufactured,
XXXX
= a unique integer for the density float
• 4.0 in • 4.0 in phase separation • 3.0 in
• 2.0 in non ‐ density
water float
• 2.0 in standard ‐ standard
density water float (1.5 inch
minimum water level)
• 2.0 in low water ‐ low water
density water float (1 inch
minimum water level)
• Custom
B7053686719512
S/N: 13240161
Exa m ple De n sity Code
Exa m ple Se r ial Nu m be r