Veeder-Root TLS-450PLUS Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 69

Veeder-Root TLS-450PLUS Скачать руководство пользователя страница 20

Initial Setup Of The Console Using Workflow Wizard

Setup>Communication>IFSF

16

Setup>Communication>IFSF

This screen lets you configure communication based on International Forecourt Standards
Forum (IFSF) standards for a TLS over TCP/IP or a LonWorks

®

card (LON Module). These

international standards for petroleum retail facilitate the interoperability of service stations
and equipment.
NOTE: A single console cannot support both TCP/IP and LON Module communications simul-
taneously, even though a site may have a mixed configuration on different consoles. The
maximum number of tanks a site can support is 30.

Configured

Touch the radio button to enable or disable IFSF communication.

Device

The device used for communication. Choices are: LON Module (if installed) or Eth1 for Ether-
net Port 1 (for TCP/IP), depending on your hardware configuration.

NOTE: On the TLS450PLUS, Ethernet Ports 2a and 2b are not available for IFSF configuration.

Protocol

The protocol used for IFSF. The choice is: IFSF-China1. This
field is not available with the LON Module device option.

Node Id

The ATG Node Identifier. Each IFSF tank gauge present on a
network must have a unique node ID. The default is 01, but
you can change it as required. This field is not available with
the LON Module device option.

NOTE: With a LonWorks

®

card, the Node ID is set using the

IFSF Node Address Dip Switch on the IFSF Interface Module
during installation. Refer to the Console Troubleshooting
section of the TLS-450PLUS Troubleshooting manual (P/N
577014-075) or the Troubleshooting section of the TLS4 /
8601 Series Consoles Troubleshooting manual (P/N 577014-
058), as appropriate, for more information on IFSF module
cable connector assembly and Node ID switch settings.

UDP Port

The port used for User Datagram Protocol (UDP) communi-
cation. The default is 3486, but this field can be edited if you
need to use a different port (1024-65535). This field is not
available with the LON Module device option.

TCP Port

The port used for Transmission Control Protocol (TCP) con-
nection requests. The default is 9000, but this field can be
edited if you need to use a different port (1024-65535). This
field is not available with the LON Module device option.

System Status

07/07/2016 09:10 AM

0 Warning(s)
0 Alarms(s)

Print (0)

Exit

Actions

Previous

Next

Setup

Enabled

Configured

Disabled

Device

LON Module

Communication

IFSF

Node Id

01

UDP Port

3485

TCP Port

9000

«
...
18
19
20
21
22
...
»

Содержание TLS-450PLUS






































































Отзывы:

Нет отзывов