![background image](http://html.mh-extra.com/html/vbrick/9000-series/9000-series_admin-manual_857502178.webp)
170
© 2015 VBrick Systems, Inc.
SNMP. ESD is converted to LDS per MISB standard 0601 and MISB EG 0104.5. The LDS
metadata packets PTS (timestamp) source is the system capture time of the first byte of ESD
data.
To configure ESD to LDS:
1. Navigate to Encoder Configuration > Video.
2. Set
KLV
to
ESD to LDS
.
3. Configure the data to be streamed in the
ESD Field
as Field One, Field Two (default), or
Field One and Two.
4. Navigate to Encoder Configuration > Streams.
a. Set Transport Type to
MPEG2TS
.
b. Check
Enable KLV
.
c. Configure other advanced settings as necessary.
5. When done the data present in the stream (defined by the ESD Field) will be encoded
and delivered with the stream.
6. To view ESD throughput, go to Monitor > Encoder Status > Monitor Video Input
Local Data Sets (LDS) Passthrough
Serial LDS Passthrough
Serial Local Data Set (LDS) Passthrough uses the encoder's serial (COM) port as an out-of-
band mechanism to embed KLV data in the video stream at a significantly higher bit rate
than ESD to LDS (and with no character limit). KLV data from a proprietary device is input
via the standard RS232/422 interface on the encoder and is embedded in the transport
stream as KLV metadata per MISB standard 601.3 and MISB Standard 0604 Section 6.2. The
metadata PTS (timestamp) source is configurable as the LDS packet's capture time or the
timestamp in the LDS packet.
To configure LDS Serial Passthrough:
1. Connect an input device to the serial (COM) port on the encoder.
2. Navigate to System Configuration > Advanced Configurations > Passthrough page.
a. Set Passthrough State to
Initiator
and Destination to
KLV
. Set the Baud Rate, Stop
Bits etc. to the values recommended by the input device manufacturer.
3. Go to Encoder Configuration > Video Input.
a. Set
KLV
to
Serial LDS Passthrough
.
4. Go to Encoder Configuration > Streams.
a. Set Transport Type to
MPEG2TS
.
b. Check
Enable KLV
.
c. Configure other advanced settings as necessary.
SDI LDS Passthrough
SDI LDS (Local Data Sets) Passthrough uses the encoder's SDI port as an out-of-band
mechanism to embed KLV data in the video stream at a significantly higher bit rate than ESD
to LDS (and with no character limit). KLV data from the SDI port is input to the encoder
and is embedded in the transport stream as KLV metadata per MISB standard 601.3 and
MISB Standard 0604 Section 6.2. The metadata PTS (timestamp) source is configurable as
the LDS packet's capture time or the timestamp in the LDS packet.
Содержание 9000 Series
