Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 87

Страница: 87 / 110

RDA 400-450 S

Ver.3 29.06.2007

The drill can be raised although

the lift stop is engaged!

- Check whether the magnetic valve (C) on the valve

block receives current. See

Hydraulic electric valves

under ”

5.1.3 Hydraulic electric valves” on page 83.

- Check the low-lift switch as explained above.

If the lift stop valve does not receive
current:

- See ”

5.1.1 Electric fault” on page 82.

If the lift stop valve receives cur-
rent:

- See ”

5.1.2 Hydraulic fault” on page 82.

The drill cannot be raised and/or

lowered!

- Check whether the lift stop or low-lift mode has been

set.

- See ”

5.1.2 Hydraulic fault” on page 82.

If the drill cannot be raised:

- Check whether the lift stop or low-lift mode has been

set.

- See ”

5.1.2 Hydraulic fault” on page 82.

- Check whether the lift stop valve (C) receives current

as a result of a shortcircuit or another fault. See

Hy-

draulic electric valves

under ”

5.1.3 Hydraulic elec-

tric valves” on page 83

- Switch off the Control Station and check whether the

drill can be raised. If it is still not possible to raise the
machine, the fault can be found in the hydraulic sys-
tem.

- Check whether a shortcircuit has occurred in the cable

harness or the intermediate cable and which function
is affected.

The Control Station generates an

alarm of too low or too high fan

speed!

NOTE!

The alarm is not generated if the fan hose has

come loose or the ejector elbows are not in the correct
positions.

Hydraulic fan:

- Check whether the hydraulic hoses are correctly con-

nected and that the hydraulic connector is pressurized.

- Check the programming of the Control Station.

- Have the pressure and flow been correctly set on the

tractor (130 bars and at least 35 l/min.)? Has the flow
valve of the tractor been correctly set?

- Has the fan speed regulator been correctly set? (Op-

tional; this is used when the tractor does not feature an
inherent flow regulator device.)

Содержание Rapid RDA 400S















































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Инструкция по эксплуатации

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды