Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 110

background image

Troubleshooting

82

Ver.3 29.06.2007

5

Troubleshooting

5.1

General information on troubleshooting

Many of the functions of the drill are controlled by a series of electrical, hydraulic and mechanical
components. A good way to exclude many of the sources of faults from the start is to first deter-
mine whether the fault is electrical. Because of this, first check whether the electric circuit is
closed to the last electric component in the chain.

Then continue troubleshooting by first performing easy inspections, in order to quickly exclude
other sources of faults.

Carefully read the attachments

”6.3 Hydraulic diagram” on page 98

and

”6.4 Electrical system”

, which can be useful during troubleshooting. Also study the descriptions under

Control station” on page 40

.

5.1.1

Electric fault

General checks for electrical faults:

!

Is the Control Station properly connected to the tractor?

!

Is at least 12 V reaching the Control Station from the tractor?

!

Have the + (brown) and ground (blue) been connected properly?

!

Check whether the automatic fuse of the Control Station has tripped.

!

Check the settings on the Control Station

!

Check whether both connectors of the intermediate cable are correctly connected to the Control
Station and Workstation.

!

Check that the connectors and sleeves of all 4-pole switch connectors are clean, free from dam-
age and are not depressed. Spray the connectors with contact spray, type 5.56.

!

Check whether the intermediate cable is pinched or otherwise damaged.

5.1.2

Hydraulic fault

General checks for hydraulic faults:

!

Check that the hydraulic hoses have been connected to the correct hydraulic coupling on the
tractor. Hoses with the same colour coding constitute a pair.

!

Make sure the hydraulic hoses' quick couplings are dimensioned for and fit the couplings on
the tractor. A number of couplings are available in the market, however, although most are
standardized problems still exist. Problems that may appear could be that female and male cou-
plings operate as non-return valves, i.e. that the machine can be raised but not lowered or vice
versa. The problem may be aggravated by a high flow rate or worn couplings.

«
...
80
81
82
83
84
...
»

Содержание Rapid RDA 400S















































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

Бренд: NORLUX Страницы: 2

Бренд: Panasonic Страницы: 174

Бренд: Rain-Flo Irrigation Страницы: 20

Attest Auto-reader 390

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Steri-Vac GS Series

Бренд: 3M Страницы: 52

Бренд: Daga Страницы: 24

Бренд: DAF Страницы: 68

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: EarthQuake Страницы: 12

Бренд: Pari Страницы: 2

Бренд: Gamry Instruments Страницы: 69

Бренд: Gamry Instruments Страницы: 30

Бренд: Gamry Instruments Страницы: 88

Бренд: Rayger Страницы: 2

AquaPure Ei Series

Бренд: Jandy Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды