Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 74

Страница: 74 / 110

Maintenance and service

Ver.3 29.06.2007

4.7

Lubrication points

Be safety conscious and do not crawl under the drill to lubricate. Lubricate from above, or support
the drill securely on trestles. See

”1 Safety regulations” on page 6.

Lubricate regularly as shown below: the disc bearings should be greased until grease appears or
by 2-3 strokes of the grease gun.

The lubrication chart with picture references can be found in the Spare Parts list.

Grease into all grease nipples at the intervals specified and always after pressure washing the drill.

Never direct water onto a bearing. It is easy to spoil seals and ball bearings with a pressure washer
since water can be forced into the bearing and cause rusting.

Lubricate at the end of each season.

Table 4.1 Lubrication points and intervals

Lubrication intervals

Lubrication points

100 ha

500 ha/

season

Qty

400/450

Bout markers

Drive wheel chain (mechanical feed output)

Drive wheel suspension (mechanical feed output)

Hinges on centre and side sections, wheel beam pivot X

Parallel linkage

Lifting ram head

Disc bearing

32 / 36

Wheel hub

16 / 18

Wheel fork

16 / 18

Transmission chain (hydraulic feed output)

Oil filter replacement (hydraulic feed output)

Intermediate packer (option)

Wing packer (option)

Содержание Rapid RDA 400S















































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Инструкция по эксплуатации

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды