Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 91

Страница: 91 / 110

RDA 400-450 S

Ver.3 29.06.2007

5.3

Alarm list

1 Low seed level.

- Check the seed level of the seed hopper.

If there is seed in the seed hopper:

- The sensitivity of the sensor has been incorrectly set.

5 The seed output device does

not rotate.

If the seed box does not move:

- Check whether the transmission between the drive

wheel and the seed box is intact.

If the alarm is generated even
though the seed box rotates:

- Check which alarm time has been programmed.

- Check the cables, connectors and connections.

- Check the operation of the sensor. The LED of the

sensor should light when the toothed plate passes. The
distance between the sensor and the toothed plate
should be 1 - 2 mm. Adjust if necessary.

A lit LED, however, is not necessarily any guarantee
that the sensor is operating.

- Check the condition and mounting of the toothed

plate.

13 Tramlining.

- The alarm is generated if tramlining does not take

place when the Control Station outputs a tramline sig-
nal or if tramlining takes place when the Control Sta-
tion does not output a tramline signal.

- Check the function of the tramline components in the

distributor head: motor, turn plate, springs and doors.
Clean if necessary.

- Check the cable, connector and connection of the sen-

sor.

- Check the sensor.

Содержание Rapid RDA 400S















































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Инструкция по эксплуатации

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды