Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 89

Страница: 89 / 110

RDA 400-450 S

Ver.3 29.06.2007

- Check whether the tooth wheel in the seed box is dam-

aged.

- Check whether the inductive detector is sufficiently

close to the rotating tooth wheel. Adjust if necessary.

The area meter/speedometer

has no indication or an incorrect

indication!

Mechanical output:

- Does the sensor receive a signal from the drive wheel

shaft sensor under the chain guard? Disassemble the
guard and inspect the sensor. See ”

5.1.5 Inductive de-

tector” on page 84

- Check the cable, connector and connection of the sen-

sor.

- Has the Control Station been programmed with the

correct drive wheel circumference (usually 240 cm)?
See

”2.21.3 Programming” on page 47.

Increase the value in case of too small an area or too
low a speed.

Decrease the value in case of too large an area or too
high a speed.

Hydraulic output:

- Has the Control Station been programmed with the

correct number of pulses per metre? See ”

2.21.3 Pro-

gramming” on page 47

If the value in the area/speed field is too low, then re-
duce the number of pulses per metre.

If the value in the area/speed field is too high, then in-
crease the number of pulses per metre.

The tramline doors seize!

- Are the doors blocked or wedged up due to seed or

rubbish?

In this case dismantle the glass cover on the distribu-
tor head and clean.

The drilling depth of the centre

and side section differs!

- Check whether the long ram rod of the folding ram is

completely extended and that the rod does not slowly
retract during driving.

- Check the setting on the wing sections, see

”2.9 Ad-

justing the wing sections” on page 20.

- Check the adjustment of the cranks on the wing sec-

tions, see

”2.8 Adjusting sowing depth” on page 20.

Содержание Rapid RDA 400S















































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Инструкция по эксплуатации

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды